Page 1
LFLED5MBR INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.
FIXTURE MOUNTING
THE FIXTURE IS MARINE LISTED, OUTSIDE TYPE (SALTWATER).
Mount to the supplied weatherproof junction box and cover
plate as shown. To ensure weatherproof seal, apply weather
proof silicone sealant around the edge of the wall coverplate
or surface box. This is especially important with an uneven
wall surface
1. Seal arm thread using teon tape or silicone sealant.
2. Thread xture into Cover Plate.
3. Connect wires as shown in the wiring diagram.
4. Attach cover to Junction Box.
5. Aim oodlight in the direction desired and tighten
locknut and Arm Screw.
Junction Box
Cover Plate
WIRING
Universal voltage driver permits operation at 120V thru
240V, 50 or 60 Hz.
1. Connect the GROUND wire from xture to supply
ground.
2. Connect the black xture lead to the (+) LINE
supply lead.
3. Connect the white xture lead to the (-) COMMON
supply lead.
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Page 2
LFLED5MBR INSTALLATION INSTRUCTIONS
4.50
114,3[ ]
45.0°
.30
7,6[ ]
1.59
[40,4]
1.59
[40,4]
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
Mounting Tab
MOUNTING Of jUNcTION bOx
To ensure weatherproof seal, apply weatherproof
silicone sealant around the edge of the Junction Box.
This is especially important with an uneven wall surface.
1. Attach the Junction Box through the Mounting
Tabs to mounting surface with appropriate
hardware. Be sure the Wall Gasket is in place.
Dimensions for drilling are shown on reverse.
Wall
2. Attach Cover Plate to Junction Box with 10-24
1/2” brass screws provided. Be sure the Cover plate
Gasket is in place.
3. All conduit entries are 1/2” NPS. Close all unused
entries with provided Plugs. Seal all conduit entry
thread using Teon tape or silicone sealant.
Gasket
Junction
Box
Plug
Cover Plate
Gasket
Cover Plate
DrIllING TeMplaTe fOr jUNcTION bOx
The template below is not to scale. Use dimensions below.
1.59”
(40.4)mm
45.0°
0.3”
(7.5)mm
4.5”
(114.3)mm
1.59”
(40.4)mm
Page 3
LFLED5MBR INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com
TROUBLESHOOTING
1. Check that the line voltage at xture is correct.
2. If there is voltage at the lamp xture wires? If there is no
voltage, check all connections.
3. Is the xture grounded properly?
ACCESSORIES
Brass Spot Reector Kit: LSLFLEDBR
Brass 4” Round Junction Box with 1/2” NPS: VXJIBR
Mighty Cap 2” for 2 /” outer diameter pipe: MMCAP2BR
Mighty Cap 3” for 2 /” outer diameter pipe: MMCAP3BR
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool
enough to touch. Do not clean or maintain while
xture is energized.
1. Clean glass lens & xture with non-abrasive glass
cleaning solution.
2. Do not open xture to clean the LED. Do not touch the
LED.
3. Keep leaves and debris out of hood.
LFLED5MBR Cool
LFLED5NMBR Neutral
LFLED5YMBR Warm
©2012 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
LFLED5MBR-IN-0513
Easy Installation & Product Help
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly sales@rabweb.com
Loading...