Page 1
IMPORTANT
READ CAREFULL Y BEFORE INST ALLING FIXTURE. RET AIN THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fi xtures must be wired in accordance with the National Electrical Code and
all applicable local codes. Proper grounding is required for safety.
THIS PRODCUT
MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fi xture.
No user serviceable parts inside.
GOOSENECK LED INSTRUCTIONS
1
1. Thread the Bushing onto the Arm.
2. Feed leads through the Arm.
3. Mount Housing to Bushing with
three set screws. Check that
Bushing Gasket is seated properly.
4. Tighten all Set Screws.
5. Loosen Swivel Screw and adjust
fi xture to desired angle. Tighten
Swivel Screw.
6. To ensure weatherproof seal use
Tefl on tape on Arm threads or use
weatherproof silicone sealant between Arm and Bushing
Housing Mounting
Bushing
Arm
Housing
Swivel
Screw
Set Screws (6)
1. Insert arm into Wall Plate.
Tighten Set Screws.
2. Make supply wiring connections in
recessed box with UL approved
connectors.
3. A universal voltage driver permits
operation at the following voltages,
50 or 60Hz.
13W 120V thru 277V
4W 120V thru 240V
4. Mount Wall Plate to the wall with
hardware appropriate for your
mounting surface.
5. To ensure weatherproof seal, apply
weatherproof silcone sealant around
the edge of the Wall Plate. This is
especially important with an uneven
wall surface.
Arm Mounting to Wall and Wiring
Set Screws
Bushing
Gasket
Wall Plate
Optional
Photocell
Note: These instructions do not cover all details or variations in equipment
nor do they provide for every possible situation during installation, operation
or maintenance.
Thank you for buying RAB lighting fi xtures. Our aim is to design the best quality products to
get the job done right. We’d like to hear your comments. Call the Marketing Department at
888-RAB-1000, or email: marketing@rabweb.com
Pat. Pending
Input Color
Lumens Watts Effi cacy(LPW) CRI Temp(K)
GNLED13Y 556 16 36 86 3000K
with Flood Refl ector & Frosted Lens
GNLED13YS 571 16 37 86 3000K
with Spot Refl ector & Clear Lens
GNLED13YR 535 16 35 86 3000K
with Rectangular Refl ector & Clear Lens
GNLED13N 643 15 43 87 4000K
with Flood Refl ector & Frosted Lens
GNLED13NS 643 15 43 87 4000K
with Spot Refl ector & Clear Lens
GNLED13NR 604 15 40 87 4000K
with Rectangular Refl ector & Clear Lens
Additional Lighting Facts labels see www.rabweb.com
Page 2
2 3
CAT# GSST
GSAC Shade
Shade Mounting
screws(4)
Housing
Shade Mounting
Screws (4)
GSST Shade
Housing
1. The Shade mounts to the Housing
with four Shade Mounting Screws
provided with the Shade.
2. Shade has keyhole slots for easy
installation.
Angled Cone Shade
CAT# GSAC
1. The Shade mounts to the Housing
with four Shade Mounting Screws
provided with the Shade.
2. Shade has keyhole slots for easy
installation.
Angled Dome Shade
CAT# GSAD
1. Remove frosted lens & frame.
2. Install Spot or Rectangular
Refl ector.
3. When installing the Rectangular
Refl ector be aware of the direction
Rectangular Light Pattern.
See illustration below.
4. We recommend using a clear lens for
these refl ector types. Replace frosted
lens and frame with clear lens & frame
provided with this kit.
5. Tighten four Housing Screws.
6. Add shade if desired.
Lens Refl ector Kit
CAT# LRFGNLED Clear Lens with Spot Refl ector and Rectangular Refl ector for
optional patterns.
1. The Shade mounts to the Housing
with four Shade Mounting Screws
provided with the Shade.
2. Shade has keyhole slots for easy
installation.
Straight Downlight Shade
Shade Mounting
screws(4)
GSAD Shade
Housing
1-888-RAB-1000 www.rabweb.com 1-888-RAB-1000 www.rabweb.com
Housing Screws (4)
Rectangular Refl ector
Rectangular Light Pattern
Orient refl ector properly within fi xture
or rotate fi xture to set beam in
orientation desired.
Spot Refl ector
Loading...