Page 1
FXLED78 INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: marketin g@rab web. com
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable
parts inside.
SLIPFITTER MOUNTING
1. The sliptter mounting ts a 2 3/8” O.D. Tenon.
Place the sliptter over the Tenon and secure the
xture with the 2 Set Screws on the side of the
sliptter.
2. Remove 2 screws on side of Round Cover Plate.
Remove the Round Cover Plate and adjust the
angle of the xture.
3. Loosen the Locking Bolt and swivel xture to
desired angle.
4. Tighten the Locking Bolt and re-attach Round
Cover Plate.
Set
Screws
Tenon
Locking
Bolt
Round
Cover
Plate
TROUBLESHOOTING
TRUNNION MOUNTING
CAUTION: UL and C-UL listed or CSA certied liquid
tight cord grip suitable for use with three conductor
type STW exible cord shall be used for connection
to a wet location outlet box provided by others.
To adjust the angle of the xture using the trunnion:
1. Loosen the Pivot Bolts & angle locking screw.
2. Adjust xture to desired angle.
3. Tighten Pivot Bolts & angle locking screw.
Pivot Bolts
WIRING
Universal voltage drivers permits operation at 120V to
277VAC, 50 or 60 Hz.
1. Connect the BLACK xture lead to the
(+) LINE supply lead.
2. Connect the WHITE xture lead to the
(-) COMMON supply lead.
3. Connect the bare copper Ground wire from xture
to supply ground.
1. Check that the line voltage at the xture is correct.
Refer to wiring directions.
2. Is the xture grounded properly?
3. Is the photocell, if used, functioning properly?
Page 2
FXLED78 INSTALLATION INSTRUCTIONS
GUARD OR SHIELD INSTALLATION
Wire Guard and Poly Shield mount with (4) #8-32
Stainless Steel Screws. Screws are provided with the
accessory. See gure 1 for Guard. See gure 2
for Shield
1. Line up guard or shield with existing pre-drilled holes
in frame as shown, tighten screws.
Figure 1
Figure 2
Pat Pending
Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.
Stainless
Steel
Screws
Stainless
Steel
Screws
GUARD & SHIELD INSTALLATION
The Wire Guard and Poly Shield can be mounted on the
same xture with (4) #8-32 screws as shown below.
ACCESSORIES
Chrome Wire Guard: GDFXLED78W
Poly Shield: GDFXLED78P
Lens & Door Replacement: LFXLED78 (bronze)
LFXLED78W (white)
CLEANING & MAINTENANCE
CAUTION: Be sure xture temperature is cool
enough to touch. Do not clean or maintain while
xture is energized.
1. Clean glass lens with non-abrasive glass cleaning
solution.
2. Do not open the xture to clean the LED. Do not
touch the LED.
FXLED78 Cool
FXLED78N Neutral FXLED78Y Warm
FXLED78-IN-1111
Loading...