RAB Lighting FLEX FLOOD Installation Instructions Manual

FLEX FLOOD

Wall Mount Installation Instructions

0˚ Down

Thank you for buying RAB lighting fixtures. Our aim is to design the best quality products so you can get the job done right.
We’d like to hear your comments. Call us at 888-RAB-1000, attention Marketing Department or email: [e-mail].

30˚ Down

0˚ Up

30˚Up

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

RAB fixtures must be wired in accordance with the National
is required for safety.

Electrical Code and and all applicable local codes. Proper grounding

WARNING: MAKE CERTAIN POWER IS OFF BEFORE INSTALLING OR MAINTAINING FIXTURE

LOCATION

Fixture should not be recessed.

WIRING

All units are factory wired for 120v. If voltages other than 120V are
required, Remove the reflector and rewire for the appropriate voltage.

1. Connect the appropriate BLACK fixture lead to the
(+) LINE supply lead.

2. Connect the WHITE fixture lead to the (-) COMMON
supply lead.

3. Fixture ground wire must be connected to supply ground.

4. All unused leads must be capped and insulated.

SUPPLY

(+) LINE BLACK

(–) COMMON

GROUND

GROUND

WHITE

GROUNDGROUND

LIGHT

FIXTURE

LAMP INSTALLATION

Caution:

manufacturer’s recommendations on lamp operation, ballast type and burning positions.

1. Disconnect power. Make sure fixture and lamp are cool enough to touch.

2.

3. Insert lamp.

4. Before closing lens door make sure frame gasket is properly seated all around fixture.

5. Close door. Tighten 4 screws.

Prior to installing, check that the lamp is of proper type and wattage. Observe lamp

Open fixture by removing the 4 door screws. Swing lens door down on hinges.

REPLACEMENT LAMPS:

High Pressure Sodium ANSI Metal Halide ANSI

Wattage Catalog # Code Wattage Catalog # Code

70 LHPS70 S62 50 LMH50 M110
100 LHPS100 S54 70 LMH70 M98
150 LHPS175 S55 100 LMH100 M90

150 LMH150PS M102
150 LMH150 M107
175 LMH175 M57

CLEANING

Clean reflector and glass refractor with nonabrasive glass
cleaning solution or detergent. Rinse with clean water.

Caution: Be sure fixture temperature is cool enough
to touch.

TROUBLESHOOTING CHECKLIST:

1. Proper lamp is installed. Lamp is not faulty.

2. Fixture is wired properly.

3. Line voltage at the fixture is proper.

4. Fixture is grounded properly.

Fluorescent

Wattage Catalog #

42 LCFL42

RAB LIGHTING Tel: 888 RAB-1000 • Fax: 888 RAB-1232 • www.rabweb.com

BEAM SPREAD ADJUSTMENT

WARNING: Make certain power is off. The lamp socket can be moved
to the rear position to provide a more narrow beam.

from the standard wide beam position (position 2)

Reflector screws (4)

1

Narrow

Standard

2

(Factory Setting)

Reflector

Loosen these
2 screws to
slide socket

To adjust socket position,remove the reflector screws and carefully lift the reflector out of the fixture. Loosen the two
socket screws and slide socket into the desired position. Tighten screws. Replace the socket bracket and reflector.

WALL MOUNTING OPTIONS

0˚ Down Position

No changes
required

Wall Mount Bolts

30˚ Down Position

Follow
1-2-3

30˚Up Position

Follow both
1-2-3 &
A,B,C below

1. Open the lens frame & remove the 4 screws
securing the reflector. Remove the reflector.

2. Remove the 2 bolts securing the
wall mount to the fixture.

3. Rotate the wall mount 180˚ and re-attach the
mounting bolts & lockwashers. Replace the reflector.

& Lockwashers

For Hands
Free Wiring:

Hook the inner
bracket hook

into the outer bracket
slot for easy
hands free wiring

Hook

0˚ Up Position

A. Remove the 4 screws securing the inner

bracket to the wall mount.

B. Rotate the inner bracket 180˚ and

re-attach the screws & lockwashers.

C. Remove the rubber plugs from the

bottom of the wall mount and re-insert
them into the screw holes at the top
of the wall mount.

MOUNTING TO A WEATHERPROOF BOX

The outer bracket has multiple mounting holes
to fit most weatherproof boxes. (recessed only)

1. Attach the outer bracket to the weatherproof

box and secure it to the inner bracket with
the 2 lock screws on the bottom of the
fixed wall mount.

2. For additional strength, the outer bracket can be

anchored to the wall by using the outer holes
on the bracket.

Outer Bracket

Outer Bracket
Inner Bracket

Rubber Plugs

Outer Bracket
Mounting Screws

Slot

Back View of

Wall Mount

Inner Bracket

Inner Bracket
Attachment
Screws

Outer Bracket
Lock Screws

Rubber Plugs

Outer Bracket
Lock Screws

EASY INSTALLATION & PRODUCT HELP

Fax Back Tech Help Line

Faxed Tips & Specs, Call our friendly experts.
24 hours/day. 8AM -5PM ET Mon. - Fri.

888 RAB-1236 888 RAB-1000

[e-mail]

RAB LIGHTING
170 Ludlow Avenue Northvale, New Jersey 07647 U.S.A.

www.rabweb.com e-mail

Visit our internet site for Your questions and requests
color product photos will be answered promptly.
and installation tips.

RAB

MAKES

IT

EASY!

© RAB LIGHTING,9541-06/04

THESE INSTRUCTIONS DO
NOT COVER ALL DETAILS
OR VARIATIONS IN

EQUIPMENT NOR DO THEY
PROVIDE FOR EVERY
POSSIBLE CONTINGENCY

BE MET IN

TO

CONNECTION WITH
INSTALLATION, OPERATION
OR MAINTENANCE.