RAB Lighting DLED4R, DLED6R Installation Instructions Manual

DLED4R DLED6R INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

DLED4R DLED6R

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

SAFETY INSTRUCTIONS

WARNING: Risk of re or electric shock. LED retrot Kit installation requires knowledge of luminaires electrical systems. If
not qualied, do not attempt installation. Contact a qualied electrician.

WARNING: Risk of re or electric shock. Install this kit only in luminaires that have the construction features and
dimensions shown in the photographs and/or drawings and where the input rating of the retrot kit does not exceed the
input rating of the luminaire.

WARNING: Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

MOUNTING

DLED Retrot unit is designed to t nominal Existing
Housings

See the list of compatible housing provided on page 2.

with openings of 4” (DLED4R) or 6” (DLED6R).

1. Thread the E26 Socket Adaptor into Existing
Housings Medium Base Socket.

2. Connect the orange Wire Connector of the E26
Socket Adaptor to DLED4R or DLED6R connector.

3. Carefully route all wires into Existing Housing (Fig.

2). Taking care not to pinch wires, squeeze either
Friction Blades (DLED4R) or Torsion Spring Arms
(DLED6R) and push up DLED4/6R.

4. Push up on DLED4/6R until it is ush to the ceiling
surface.

Friction

Blade

5.10”

DLED4R

E26 Socket Adaptor

Wire Connector

Torsion

Spring Arm

7.39”

DLED6R

Fig. 1

DLED4R DLED6R INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

Medium Base Socket

Existing Housing

Fig. 2

DLED6R

DLED4R

WIRING

WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sheet metal or other sharp
objects.

Fixture operates at 120V 60 Hz and can be dimmed with
most forward phase incandescent dimmers. For a list of
compatible dimmers see www.rabweb.com

1. Screw in medium base socket adaptor.

2. Connect GROUND wire from DLED xture to the
existing housing with # 8 screw provided to any
existing housing hole as shown or drill a new 1/8”
diameter hole.

3. Plug in wire connector between socket adaptor and
DLED xture.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.

1. Clean lens & xture with non-abrasive cleaning solution.

2. Do not open xture to clean the LED. Do not touch the LED.

TROUBLESHOOTING

Check that the line voltage at xture is correct.

1. Check that the socket adaptor is properly seated in the socket.

2. Do not attempt to modify the socket in any way.

UL CLASSIFIED FOR RETROFIT
COMPATIBILITY

Check that the existing housing is one of the following
compatible xtures.

1. Retrot has an E26 Edison screw-base.

2. DLED4R and DLED6R can be used in
with opening of 4 or 6”. These xtures are UL Classied
for retrot in the following housings:

• Halo: Housing Series H99TAT

• Elite: B4, B4IC, BL4_Bae, ID4-AT

• Nora: NS-401QAE, NS-401QAT, NSR-404QAT

• Halo: Housing Series H7x, H27x, ET7x, Ei7x, ET27x,
EI27x. Halo H750ICAT, H750RICAT, H750T and
H750TCP series recessed LED housings.

• Juno:IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21,
IC21R, TC2, TC2R

• Capri: CR1, PR1, QL1, R9ASIC

• Progress: P87-AT, P86TG

• Lithonia: L7X, L7XP

• Thomas: PST, R9ASIC/PS9RM

• Prescolite: IBXS

• Commercial Electric: H3

• Elco: EL71CA

• Elite: B6IC-AT-W

existing housings

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation
or maintenance.

Easy Answers

© 2018 RAB LIGHTING Inc.

Northvale, New Jersey 07647 USA

DLED4RR DLED6RR IN 0218

rabweb.com

Visit our we bsite for produc t info

Tech Help Line

Call our ex perts - 888 722-1000

e-mail

Answered promptly - [e-mail]

Free Lighting Layouts

Answered o nline or by reques t

DLED4R DLED6R INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

DLED4R DLED6R

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

SAFETY INSTRUCTIONS

WARNING: Risk of re or electric shock. LED retrot Kit installation requires knowledge of luminaires electrical systems. If
not qualied, do not attempt installation. Contact a qualied electrician.

WARNING: Risk of re or electric shock. Install this kit only in luminaires that have the construction features and
dimensions shown in the photographs and/or drawings and where the input rating of the retrot kit does not exceed the
input rating of the luminaire.

WARNING: Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

MOUNTING

DLED Retrot unit is designed to t nominal Existing
Housings

See the list of compatible housing provided on page 2.

with openings of 4” (DLED4R) or 6” (DLED6R).

1. Thread the E26 Socket Adaptor into Existing
Housings Medium Base Socket.

2. Connect the orange Wire Connector of the E26
Socket Adaptor to DLED4R or DLED6R connector.

3. Carefully route all wires into Existing Housing (Fig.

2). Taking care not to pinch wires, squeeze either
Friction Blades (DLED4R) or Torsion Spring Arms
(DLED6R) and push up DLED4/6R.

4. Push up on DLED4/6R until it is ush to the ceiling
surface.

Friction

Blade

5.10”

DLED4R

E26 Socket Adaptor

Wire Connector

Torsion

Spring Arm

7.39”

DLED6R

Fig. 1

DLED4R DLED6R INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

Medium Base Socket

Existing Housing

Fig. 2

DLED6R

DLED4R

WIRING

WARNING: To prevent wiring damage or abrasion, do
not expose wiring to edges of sheet metal or other sharp
objects.

Fixture operates at 120V 60 Hz and can be dimmed with
most forward phase incandescent dimmers. For a list of
compatible dimmers see www.rabweb.com

1. Screw in medium base socket adaptor.

2. Connect GROUND wire from DLED xture to the
existing housing with # 8 screw provided to any
existing housing hole as shown or drill a new 1/8”
diameter hole.

3. Plug in wire connector between socket adaptor and
DLED xture.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is energized.

1. Clean lens & xture with non-abrasive cleaning solution.

2. Do not open xture to clean the LED. Do not touch the LED.

TROUBLESHOOTING

Check that the line voltage at xture is correct.

1. Check that the socket adaptor is properly seated in the socket.

2. Do not attempt to modify the socket in any way.

UL CLASSIFIED FOR RETROFIT
COMPATIBILITY

Check that the existing housing is one of the following
compatible xtures.

1. Retrot has an E26 Edison screw-base.

2. DLED4R and DLED6R can be used in
with opening of 4 or 6”. These xtures are UL Classied
for retrot in the following housings:

• Halo: Housing Series H99TAT

• Elite: B4, B4IC, BL4_Bae, ID4-AT

• Nora: NS-401QAE, NS-401QAT, NSR-404QAT

• Halo: Housing Series H7x, H27x, ET7x, Ei7x, ET27x, EI27x

• Halo H750ICAT, H750RICAT, H750T and H750TCP series

recessed LED housings.

• Juno:IC22, IC22R, IC22W, IC22S, IC23, IC23W, IC21, IC21R,

TC2, TC2R

• Capri: CR1, PR1, QL1, R9ASIC

• Progress: P87-AT, P86TG

• Lithonia: L7X, L7XP

• Thomas: PST, R9ASIC/PS9RM

• Prescolite: IBXS

• Commercial Electric: H3

• Elco: EL71CA

• Elite: B6IC-AT-W

existing housings

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during installation, operation
or maintenance.

Easy Answers

© 2018 RAB LIGHTING Inc.

Northvale, New Jersey 07647 USA

DLED4RR DLED6RR IN 0218

rabweb.com

Visit our we bsite for produc t info

Tech Help Line

Call our ex perts - 888 722-1000

e-mail

Answered promptly - [e-mail]

Free Lighting Layouts

Answered o nline or by reques t