RAB Lighting BLED5 Square, BLEDR5 Round, BLED2X5 Square, BLEDR2X5 Round Installation Instructions Manual

BLED5 INSTALLATION INSTRUCTIONS

BLED5 Square BLEDR5 Round BLED2X5 Square BLEDR2X5 Round

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000, or email: marketin g@rab web. com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper
grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT

AND THE HAZARDS INVOLVED. WARNING: Make certain power is OFF before installing or maintaining

xture. No user servicable parts inside.

LOCATIO N

1. The Bollard should be mounted to a rm level
surface.

2. Anchor bolts may be used in new concrete
installations. Use the template provided.

3. For all other applications use anchors suitable for the
mounting surface.

ANCHOR BOLTS INSTALLATION

CAUTION: Install according to all applicable local codes.

1. Install two Anchor Bolts in concrete foundation (by

others) using the template provided. Mounting Plate
may also be used as the template. Anchor Bolts
should protrude no more than 3”.

Anchor
Bolts

Mounting
Plate

MOUNTING PLATE

Assemble xture(s) to bollard before mounting the Bol­lard to the Mounting Plate.

1. Place the Mounting Plate over Anchor Bolts.

2. Use four Leveling Screws or shims to level the

Mounting Plate.

3. Tighten assembly using the washers, lockwashers
and nuts provided.

4. Make sure supply leads extend far enough to make
xture connections.

5. Slide Gasket down around the bottom of the
Mounting Plate.

6. Use the four screws to mount the Bollard to the

Mounting Plate. Tighten securely.

Bollard

Leveling

Screws

Gasket

Mounting

Screws

Concrete

Conduit

Anchor
Bolts

Mounting
Plate

BLED5 INSTALLATION INSTRUCTIONS

MOUNTING fIXTURES

For BLED5 & BLEDR5 the window is available on one side of Bollard. Secure Bollard before installing the housing.

1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.
Fixture may hang from the tether while installing.

2. Place Bollard Gasket and Mounting Plate over recessed box.

3. Attach Mounting Plate with supplied Mounting Plate Screws.

4. Pull supply wires from box through mounting plate and wire xture as shown in the wiring section.

5. Check Housing Gasket. It should remain rmly around the inside of the Housing.

6. Align Housing to Mounting Plate.

7. Make sure all gaskets are properly seated. Tighten Housing Screws.

8. Secure the Cap Gasket and tighten the Bollard Cap with supplied screws.

Bollard

Cap

Cap
Gasket

Housing

screws

Housing

Mounting
Plate

Bollard

Gasket

Bollard

Cap

Cap
Gasket

Bollard

BLED5 INSTALLATION INSTRUCTIONS

MOUNTING fIXTURES

For BLED2x5 & BLEDR2x5, cutouts are provided on both sides of Bollard. Secure Bollard before installing the
housings.

1. Loosen Housing Screws and remove Mounting Plate. Screws will remain in place with O-ring retaining gaskets.
Fixture may hang from the tether while installing.

2. Place Bollard Gasket and Mounting Plate over cut out on Bollard.

3. Attach Mounting Plate with supplied mounting plate screws.

4. Pull supply wires from bollard through mounting plate and wire xture as shown in the wiring section.

5. Check Housing Gasket. It should remain rmly around the inside of the Housing.

6. Align Housing to Mounting Plate.

7. Make sure all gaskets are properly seated. Tighten Housing Screws.

8. Follow same steps for second xture.

9. Secure the Cap Gasket and tighten the Bollard Cap with provided screws.

Bollard

Bollard

Cap

Cap
Gasket

Housing

screws

Housing

Mounting
Plate

Bollard

Gasket

Cap
Gasket

Bollard

Cap

Bollard

Gasket

Bollard

Mounting
Plate

Housing

Gaskets

Housing­Screws

BLED5-IN-0612

BLED5 INSTALLATION INSTRUCTIONS

LIGHT

FIXTURE

(+)LINE BLACK

(-)COMMON WHITE

GROUND GROUND

ACCESSORIES

Bollard base: BOLBASE
Bollard base Retro kit: BOLBASE RETRO

Sufx “Y” = Warm 3000K LED
Sufx “N” = Neutral 4000K LED,

TROUBLESHOOTING

1. Check that the line voltage at xture is correct. Refer
to wiring directions.

2. Is the xture grounded properly?

3. Is the photocell is functioning properly (if used)?

WIRING

Universal driver permits 120V to 240V, 50 or 60Hz.

1. Connect the black xture lead to the (+) LINE
supply lead.

2. Connect the white xture lead to the (-) COMMON
supply lead.

3. Connect the bare copper Ground wire from xture to
supply ground.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool
enough to touch. Do not clean or maintain while
xture is energized.

1. Clean glass lens with non-abrasive glass cleaning
solution

2. Do not open xture to clean the LED.

BLED5 Cool LED Square Steplight

BLEDR5 Cool LED Round Steplight

SLED Round: US pat. D612,974, CA Pat. pending,
CN Pat. pending
SLED Square:.US pat. D612,975, CA Pat. pending,
CN Pat. pending

Note: These instructions do not cover all details or variations
in equipment nor do they provide for every possible situation
during installation, operation or maintenance.

BLED5 INSTALLATION INSTRUCTIONS

BLED5N Neutral LED Square Steplight BLEDR5N Neutral LED Round Steplight

BLED5Y Warm LED Square Steplight BLEDR5Y Warm LED Round Steplight

BLED5 INSTALLATION INSTRUCTIONS

ANCHOR BOLT TEMPLATE fOR BLED BOLLARD

Conrm dimensions before using as a template. If possible use the actual mounting plate as your template.