RAB Lighting ALED Series Installation Instructions Manual

R

ALED POST TOP INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required
for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

FIXTURE ASSEMBLY

1. Feed the (3) Housing wires through one of the three
Rods.

2. Clip the (3) Rods onto the Housing. Be sure the Housing
clips are properly engaged onto the Rods.

3. Feed Fixture Wires through the Tenon Pole Adaptor.

4. Slide Tenon Pole Adaptor on three Rods. Be sure the
notches face the inside of the Tenon Pole Adaptor.

5. Tighten the (3) Set Screws at the Tenon Pole Adaptor to
secure Rods.

POLE MOUNTING

1. Make the wiring connections with UL approved
connectors knot the wires for strain relief.

2. Slip Tenon Pole Adaptor over 2 3/8” diameter tenon and
secure with the set screws on the side of Tenon Adaptor.

Set Screw
(to secure Tenon)

Tenon Pole
Adaptor

Set Screw
(to secure Rods)

Housing­Wires

Rods (3)

Housing
Wires

Housing

Note: These instructions do not cover all details or variations in equipment nor do they provide for every possible situation during
installation operation or maintenance.

R

LIGHT

FIXTURE

(+)LINE BLACK

(-)COMMON WHITE

GROUND GROUND

Call our experts 888 RAB-1000

Northvale, New Jersey 07647 USA

Visit our website for product info

Answered promptly [e-mail]

ALED POST TOP INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [e-mail]

WIRING

Universal voltage driver permits operation at 120 to 277VAC,
50 or 60Hz.

1. Connect the black xture lead to the (+)

LINE supply lead.

2. Connect the white xture lead to the (-)

COMMON supply lead.

3. Connect the bare copper Ground wire from xture to

supply ground.

CLEANING & MAINTENANCE

CAUTION: Be sure xture temperature is cool enough to
touch. Do not clean or maintain while xture is ener­gized.

1. Clean glass lens with non-abrasive glass cleaning
solution.

2. Do not open xture to clean the LED. Do not touch the
LED.

010V DIMMABLE WIRING

Universal voltage driver permits operation at 120V thru
277V, 50 or 60 Hz. 0-10V control wires must be rated for 300V
minimum. For 0-10V Dimming, follow the wiring directions as
in g. 2.

1. Connect the black xture lead to the (+) LINE supply lead.

2. Connect the white xture lead to the (-) COMMON supply
lead.

3. Connect the GROUND wire from xture to supply ground.
Do NOT connect the GROUND of the dimming xture to
the output.

4. Connect the purple xture lead to the (V+) DIM lead.

5. Connect the gray xture lead to the (V-) DIM lead.

6. Cap the yellow xture lead. Do NOT connect.

Fig. 2

TROUBLESHOOTING

1. Check that the line voltage at xture is correct. Refer to
wiring directions.

2. Is the xture grounded properly?

ALED5T52 ALED5T78

©2012 RAB LIGHTING Inc.

ALED5T78 IN-0514

Easy Installation & Product Help

Tech Help Line

rabweb.com

email