Rabbit Air SPA-421A, SPA-582A User's Guide

Download

Rabbit Air

www.RabbitAir.com

Model No. SPA-421A and SPA-582A

User's Guide

Safety Instructions

WARNING: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using the BioGS air purifier.

• Use only as directed by the BioGS air purifier user's guide. To reduce the risk of electric shock, do not attempt to service the product

in any way other than in the manner described in this user's guide.

• Please observe extreme caution when the BioGS air purifier is used by or near children.

• The BioGS air purifier is for indoor use only.

• BioGS air purifier operates at 120V AC and 60Hz only.

• The BioGS air purifier is not intended for use in bathrooms, laundry areas and other damp indoor environments. Keep the BioGS

TM TM

air purifier away from water at all times. Never place the unit anywhere near bathtubs or sinks.

• Do not use the BioGS air purifier near fireplaces or in areas where flammable or combustible products or vapors may be present.

• Turn off the BioGS air purifier before unplugging it from power outlet.

• Always unplug the BioGS air purifier from power outlet when not in use and before servicing or cleaning the unit.

• To reduce the risk of electric shock, the BioGS air purifier has a polarized plug. This plug will fit in a polarized outlet only one way. If

the plug does not fit into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet. Do not alter the plug in any way.

• To reduce the risk of electric shock, do not touch the BioGS air purifier or its power plug with wet hands.

• Always keep the BioGS air purifier cord away from heated surfaces.

• Do not operate BioGS air purifier if the plug or cord appears damaged or is damaged. Return the unit to authorized service facility

for examination and repair.

• Any attempts to open or repair the BioGS air purifier without written permission from Rabbit Air will void the warranty and could

cause serious personal injury to the user and/or result in severe damage to the unit.

• Do not use the power cord to lift, pull, carry or drag the BioGS air purifier. Avoid pulling the power cord against or around sharp

corners or edges.

• Do not unplug the BioGS air purifier by pulling its power cord. Remove the power plug from its outlet by grasping the plug itself and

pulling gently.

• When the BioGS air purifier plugs into the power outlet, do not put any object into the openings of the unit. Also keep all fingers,

body parts, hair, jewelry and loose clothing away from the openings.

Cautions Concering the Operation of BioGS Air Purifier

• Do not block the intake and air outlet.

• Do not use the unit near or on hot objects such as a stove.

• Do not use the unit where it may come into contact with steam.

• Do not use the unit on its side.

• Do not install the unit in a location where there is heavy generation of oily residue such as kitchen.

• Do not use detergent or soap to clean the unit.

• Do not operate the unit without installing the filters.

• Do not wash & reuse the BioGS HEPA filter.

• When transporting the unit, always hold the handle on the back of the unit.

Remote Control Limitations

• Do not use the remote control near inverter lighting equipment or electronic light fixtures.

• Avoid leaving the remote control in direct sunlight. Heat may interfere with remote control signals.

Installation Guidelines

• Keep a distance of at least 3 feet of space between air purifier and any equipment which involve electric wave such as televisions, radios or wave clocks.

• Leave at least 2 inches of space between the wall and the BioGS air purifier.

• Avoid locations where BioGS air quality sensors are exposed to direct wind.

• Avoid locations where excessive dirt comes into contact with the intake or air outlet.

Part Names

Front View of Air Purifier

Air Outlet

Odor/Chemical Sensor

Detects odor such as tobacco smoke, pets, household chemicals and etc.

Back View of Air Purifier

Main Unit Display

Indicator lights and main control button for the air cleaner.

Filter Reset Button

After replacing or cleaning the filters, press the filter reset button to reset the indicators.

Dust/Particle Sensor

Detects dust, smoke, pollen, animal dander and etc.

Washable charcoal based

activated carbon filter

Absorbs and removes common household odors, VOCs, chemical smells & cigarette odor.

BioGS HEPA Filter

"Next Generation" HEPA filter made of bio-engineered fiber traps and destroys the allergens such as pet dander, dust mite and pollen which accumulate on the filter.

Nano-Silver Pre-Filter

Aids in Sterilization and collects pet hair, Large size allergens and dust.

Front Panel

Slot to place remote control

Handle

Power cord

Power plug

Main Unit Display

Odor/Chemical Level Indicator

Indicates chemical and odor levels by changing color in five steps from light green, green, yellow, orange to red. (Light Green represents good air quality & Red represents poor air quality)

Operation Mode Indicators

Indicator lights for Auto Mode, Turbo Mode, Sleep Mode and Pollen Mode.

Timer Display Indicator

Unit will turn off automatically after preset time duration.

Remote Control Receiver

Remote Control Operation

Transmitter

Auto Mode Button

The fan speed of the air cleaner will change automatically depending on the amount of impurities in the air as detected by the dust and odor sensors.

Silent or Sleep Mode Button

Unit will operate at a lower fan speed and the operation is totally silent.

Timer Button

Used to set the Off Timer. The set time switches every time the button is pressed as shown below.

1 hours 2 hours

off timer

The indicator light shows the remaining time. The unit stops operating when the timer is up.

4 hours

Unit Status Indicator

Unit status indicator will stay on when the air purifier is on standby or is operating. The indicator will flash for 15 seconds when the air purifier is detecting the air quality baseline.

Main Control Button

You can change operation modes, turning the unit on and off or changing the fan speed of the unit by using this control button.

Rabbit Air

Particle/Dust Level Indicator

Indicates level of dust or particles by changing color in five steps from light green, green, yellow, orange to red. (Light Green represents good air quality & Red represents poor air quality)

Negative Ion Indicator

Unit will generate negative ion when this indicator is on.

Filter Cleaning Indicator

The filter cleaning indicator will illuminate when it is time to clean the filters and reset the indicator.

Filter Replacement Indicator

The filter replacement indicator will illuminate when it is time to replace the filters and reset the indicator.

Fan Level Indicator

Indicates the fan speed of the air purifier.

Standby Button

Pressing this button will put the unit to standby mode.

Negative Ion Mode Button

Unit will generate negative ion by pressing this button.

Turbo Mode Button

Unit will operate at the highest fan speed for 10 minutes and then changes to Auto mode.

Pollen Mode Button

This mode of operation is good for the pollen season. The unit will alternate between low and medium fan speed every 10 minutes

Fan Level Button

The fan speed can be switched between Low, Medium, High and Turbo.

Preparation

List of Parts

BioGS HEPA Filter

Nano-silver Pre-Filter

1. Filter Installation

To maintain the quality of the filters, they are placed in the unit within plastic bags.

CAUTION

Please remove the filters from the plastic bags before using the unit.

Place the unit facing up and Remove the front panel

Step 1

Lay the unit on a flat surface such as table or floor. Make sure not to pinch the power cord on the rear of the unit.

Put your hands at the bottom of the front panel and lift the panel up gently.

Remove Plastic bags from the BioGS HEPA filter and Washable charcoal based

Step 2

activated carbon filter.

Remove the pre-filter from the unit.

Remove Plastic bags from the BioGS HEPA filter and Washable charcoal based activated carbon filter.

First, install the Washable charcoal based activated carbon filter. The filter handle should be facing the front panel.

Install the BioGS HEPA filter with the word "Front" on the filter frame face toward you.

Re-insert the pre-filter and the front panel.

Step 3

First, install the pre-filter. The filter handles should be facing the front panel.

Re-insert the front panel back to the unit. Press in the hooks on the bottom of the front panel into the unit. You should hear a "click" sound if installed properly.

Inserting Battery in the Remote Control.

Flip over the remote control. Press and slide out the battery holder

Insert battery with positive side facing up.

Washable charcoal based activated carbon filter

Remote Control

Rabbit Air

Close the battery holder.

3V Lithium Coin Battery

Battery Information

The batteries for this remote control are for initial use only. Change the batteries when necessary. Incorrect usage of the batteries may cause battery fluid leakage and/or damage. When replacing battery, replace battery with new one of the same type (Use 3V Lithium Coin Battery). When not using the unit or remote control for an extended period, remove the batteries.

(This prevents malfunction of the remote control from battery fluid leakage.)

The batteries are for initial use only and may be depleted within 1 year.

How to set up Home Air Quality Baseline.

When the power plug is inserted into the wall outlet, the unit will register the current home air quality as a baseline (reference point). It will take 15 seconds for the Air Quality Level Sensors to indicate the air quality level. You will see the unit status indicator on the

main unit display flashing for 15 seconds. The Air Quality Level Indicator displays a color-coded indicator light depending on relative changes to the environment from the

time the power plug is inserted into the wall outlet and thereafter. The Air Quality Level Indicator can be turned off using the Standby button on the remote control.

Important

When the air is heavily polluted at the time the power plug is inserted, the unit may not work properly in auto mode because the baseline or reference point is too high. To reset the air quality baseline, unplug the unit and re-insert it when the air quality is in normal condition.

Operation

Unit can operate by using either:

1. Remote Control

2. Main Unit Control Button. (Some features will not be available by using just the unit control button.)

The remote control or main unit control button can activate the following modes.

Automatic mode

Silent mode

Manual mode

Start operation.

Auto mode

Turbo mode

Silent mode

Manual mode

Pollen mode

Timer mode

Negative Ion mode

Remote Main

Unit automatically select fan speed based on air quality.

Unit operates at turbo speed for 10 minutes and then returns to auto mode.

Unit operates at the lowest and the quietest fan speed.

Unit operates at the pre-set fan speed.

The unit will alternate between low and medium fan speed every 10 minutes.

Unit operates for a pre-determined time, then shuts off.

Turns negative ion generator on/off.

Remote control operation

Activate remote control by pressing the any button. Be inline with the front side of the unit. (The maximum range of effectiveness is 23 feet)

Avoid exposure to direct sunlight; inverter lamp and high frequency equipment. It might affect performance of remote control.

If air purifier responds properly, a short beep will sound and operation will start. Please try to replace the battery if the remote control does not work properly.

R a

b b i

t A

i r

Auto Mode

The fan speed of the air cleaner will change automatically depending on the amount of impurities in the air as detected by the dust and odor sensors.

Press the Auto Mode button on the remote control to start the Auto Mode operation.

Strat operation

Air Quality

Level Indicator

Fan Speed

Rabbit Air

Turbo Mode

The air purifier operates at turbo fan speed for 10 minutes and then changes to Auto mode.

Press the Turbo Mode button on the remote control to start the Turbo Mode operation.

Mode of Operation

ATTENTION

The unit will operate at silent fan speed when the air quality level is normal or is below the baseline level.

Turbo Mode

Mode of

Operation

Silent Mode

The air purifier operates at silent fan speed continuously.

Press the Silent Mode button on the remote control to start the Silent Mode operation.

First 10 Minute After 10 Minute

Silent Mode

Silent Low Med High Turbo

Manual Mode

The air purifier operates at the selected fan speed continuously.

Press the Fan Level Button on the remote control to start the Manual Mode operation.

Manual Mode

Low

Mode of

Operation

Turbo

Medium

High

Mode of

Operation

Negative Ion Mode

Unit generates negative ion by pressing Negative Ion Mode button.

Negative Ion Mode

Mode of

Operation

Rabbit Air

Pollen Mode

This mode of operation is recommended for the pollen season. The unit will alternate between low and medium fan speed every 10 minutes.

Press the Pollen Mode button on the remote control to start the Pollen Mode operation.

Pollen Mode

Mode of

Operation

Timer Mode

The unit will stop operating when the timer is up.

Press the Timer Mode button on the remote control to start the Timer Mode operation.

Timer Mode

Used to set the Off Timer. The set time switches every time the button is

Timer

settings

pressed as shown below.

1 hours 2 hours

off timer

The indicator light shows the remaining time. The unit stops operating when the timer is up.

4 hours

ATTENTION

The BioGS Air Purifier produces millions of healthy "negative ions" to improve the air you breathe and freshen your indoor environment through the use of anion generator inside of the unit discharge. The negative ions help reduce suspended particulate, and at the same time, make it difficult for pollutants to become airborne in the first place. Negative ions are odorless, tasteless, and invisible molecules that we inhale in abundance in certain environments. Think mountains, waterfalls, and beaches. Scientific research shows negative ions may help to alleviate depression, relieve stress, and boost our daytime energy. The Rabbit Air BioGS air purifier uses non-ozone clusters to produce negative ions, therefore, our unit has zero ozone emission and it is harmless to human and the environment.

Standby

Press the Standby button on the remote control to stop the unit.

Main Unit Control Button

You can control the air purifier by the main unit control button. When you press the button, the operation mode of the air purifier will be changed according to the following diagram.

Auto Mode

Silent Mode

Low Speed

Medium Speed

High Speed

Turbo Speed Standby

Cleaning and Maintenance

To maintain optimum performance of this product, please clean the unit and filters as recommended.

CAUTION

1. Cleaning the Unit Surface and Air Quality Sensors

To clean the unit surface:

The unit surface should be cleaned at least once a month or sooner depending on the air quality of the room.

Use a clean, dry cloth to wipe the external surfaces of the air purifier. Use a damp cloth to remove stubborn stains and dirt build up if necessary. Do not use commercial cleaning agent as it may damage the unit surface. Clean the air inlet and outlet with a dry cloth or a vacuum cleaner. (Fig. 1)

To clean air quality sensors:

The air quality sensors should be cleaned at least once a month or more depending on the air quality of the room.

Take off the front panel. Clean the surface of the sensor opening with a vacuum cleaner.

When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result.

(Fig. 1)

2. Cleaning the Pre-Filter

To clean the pre-filter:

The pre-filter should be cleaned at least once a month or when the filter cleaning indicator illuminates.

After removing the front panel from the air purifier, run a vacuum cleaner with a nozzle or brush attachment on low power setting along the filter to pick up the pet hairs or particles. (Fig. 2)

(Fig. 2)

If your pre-filter appears to have dirt that has not been removed by vacuuming, please follow the steps below to wash the pre-filter.

Remove the pre-filter from the unit. (Fig. 3) Fill the sink with lukewarm water and gently wash the filter under the water for 2-3 minutes or until it is

completely clean. Rinse the filter with clean tap water. Use towel to remove any excess water from the filter. Allow the filter to dry for a few hours or overnight. When the filter is completely dry, place back into the air purifier.

(Fig. 3)

3. Cleaning the BioGS HEPA Filter

To clean the BioGS HEPA filter:

The BioGS HEAP filter should be cleaned when the filter cleaning indicator illuminates. After removing the pre-filter from the air purifier, run a vacuum cleaner with a nozzle or brush

attachment on low power setting along the HEPA filter to pick up the dust and particles (Fig 4).

4. Cleaning the Washable Activated Carbon Filter

To clean the washable activated carbon filter:

The activated carbon filter should be cleaned when the filter cleaning indicator illuminates. Remove the filter from the unit. Fill the sink with lukewarm water and add a few drops of mild household detergent (Fig. 5). Soak the filter for 10 minutes. Do not leave for an extended period of time. Rinse the filter with clean tap water. Use towel to remove any excess water from the filter. Allow the filter to dry for a few hours or overnight. When the filter is completely dry, place back into the air purifier.

To reset the Filter Cleaning or Replacement Indicator

Remove front panel. With the power on, press and hold the filter reset button for 3-5 seconds, or until the "red" filter

cleaning or replacement indicator clears itself (Fig.6).

(Fig. 4)

(Fig. 5)

(Fig. 6)

Replacing the BioGS HEPA filter

When the filter replacement indicator light comes on, replace the old BioGS HEPA filter with a new one.

To maintain optimum performance of this product, please replace the filters as recommended. The air quality and surrounding environment determines the duration and life span of the filter and while it may last longer than

expected, it is advisable to change the BioGS HEPA filter at least every 18 months or 1.5 year of unit operation.

The higher the level of pollutants, the shorter the lifespan of the filter.

Remove the front cover and the pre-filter

Install a new BioGS HEPA filer by following the instructions on step 1 and 2 (page 5).

After replacing the filter, reset the filter replacement indicator as indicated in page 10.

Follow the instruction on step 3 (page 5) and complete the filter change.

ATTENTION

Discard the used BioGS HEPA filter and do not store for re-use.

For more information on the BioGS HEPA filter replacement or to buy replacement filter, please contact Rabbit Air.

Replacing the washable activated carbon filter

Replacement indicator light will come on every 18 months, the washable activated carbon filter only need to be replaced every other time when the indicator light comes on. A single filter can last up to 3 years.

expected, it is advisable to change the washable activated carbon filter every 3 years. The higher the level of pollutants, the shorter the lifespan of the filter.

Remove the front cover and the pre-filter

Install a new washable activated carbon filter by following the instructions on step 1 and 2 (page 5).

After replacing the filter, reset the filter replacement indicator as indicated in page 10.

Follow the instructions on step 3 (page 5) and complete the filter change.

ATTENTION

Discard the used washable activated carbon filter and do not store for re-use.

Rabbit Air

Ultra Quiet Air Purifier

SPA-421A/582A

LIMITED WARRANTY

Rabbit Air warrants that your BioGS Air Purifier will be free from defects in material or workmanship for a period of Five (5) years from the date of purchase. To activate the warranty, please complete and return your warranty registration within 30 days of purchase of your air purifier to Rabbit Air. In order to ensure unit performance, the filters should be replaced with original BioGS replacement filters as recommended in this manual (the 'Limited Warranty'). Otherwise the standard warranty time in your country applies.

Within the first 30 days of purchase, Rabbit Air will replace the defective unit at no additional cost and reimburse any shipping charges. After 30 days, Rabbit Air's obligation and liability under this Limited Warranty is limited to repairing or replacing (at its sole discretion) the defective unit. The Limited Warranty does not cover replacement filters.

In the event of a malfunction or failure of your Rabbit Air BioGS Air Purifier, please contact Rabbit Air to obtain a return authorization number and the address of the service center. The return authorization number must be clearly written on the outside of the shipping box or the shipment may be refused.

Your Limited Warranty remains in effect only if your BioGS Air Purifier:

1. Is operated in accordance with the instruction provided.

2. Is connected to a proper power supply (see voltage label on machine).

3. Th re is no evidence of tampering, mishandling, neglect, accidental damage, modification, and/or repair done to the BioGS Air

Purifier by anyone other than authorized BioGS service personnel.

4. Your warranty registration has been completed and returned to Rabbit Air.

LIMITS AND EXCLUSIONS

There are no express warranties except as listed above.

THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

If a problem with the product develops during the warranty period, we will repair or replace it without charge to you. A shipping and processing fee may apply. To obtain service under warranty, please contact Rabbit Air at 1-888-866-8862 or by email at products@RabbitAir.com

Troubleshooting

Before calling for repair, please review the list below. The problem may not be due to unit malfunction.

Symptom Solution

Unit does not operate.

The remote control does

not work.

Odors and smoke are not

removed.

The unit does not operate

when cigarette smoke is

in the air or when the air is

highly polluted.

In auto mode, the unit

operates at high speed

even when the air is

clean.

The filter replacement indicator light remains

activated even after

replacing filter.

The negative ion mode

indicator light is flashing.

Check if power plug is loose.

Press the main unit control button or any buttons on the remote

Check if the battery has been depleted. (Refer to P.5)

Check if the battery is inserted correctly. (Refer to P.5)

Point the remote control directly towards the main unit display.

Fluorescent lighting flickering in the room may affect the signal of the remote control. Please service the fluorescent lights.

Clean the filters if they appear to be heavily soiled. (Refer to P.9)

Check if all the plastic bags that wrap the filters are being removed. (Refer to P.5)

Check if the unit is installed in a location that is difficult for the sensors to detect the smoke or the air quality.

Check if the odor or dust sensor openings are blocked or clogged. Clean the sensors (Refer to P.9)

The unit may not work properly in auto mode because the baseline or reference point is too high. To reset the air quality baseline, unplug the unit and re-insert it in a well-ventilated area.

The sensitivity of the sensor becomes unstable when the sensor opening is blocked or clogged. Clean the sensors (Refer to P.9).

Reset the air quality baseline, unplug the unit and re-insert it.

After replacing filters, connect the power cord to an outlet and press the filter reset button on the main unit.

With the power on, press and hold the filter reset button for 3-5 seconds, or until the "red" filter cleaning or replacement indicator clears itself (Refer to P.10).

Clean the negative ion generator inside the discharge outlet with a vacuum cleaner.

1. Mr. 2. Mrs. 3. Ms. 4. Miss

First Name Initial Last Name

Street

City

E-mail

Your date of birth:

Month Year

Marital status: 1. Married 2. Single

Date of purchase:

Month YearDay

Model number: (please refer to owner's manual or the back

of your product to locate the model number)

Serial number:

Name of store where purchased:

Do you own a house or rent?

Own Rent

Where did you first learn about Rabbit Air

products?

1. Received as a gift

2. Newspaper

3. Salesperson

4. Friend/Relative

5. Online

6. Magazine

7. Prior experience with Rabbit Air brand

8. TV

9. Other

What factors most influenced your decision to

10.

purchase this Rabbit Air product?

(check up to 3)

1. Rabbit Air reputation

2. Prior experience with Rabbit Air

3. Value for the price

4. Quality

5. Size/dimension

Apt. No.

State/Province

6. Style/appearance

7. Product availability

8. Advertisement

9. Other

What is the primary reason you purchased this

11.

product? (Check only one)

1. Relieve Allergy or Asthma Symptoms

2. Improve Air Quality for Kids

3. Improve Home Comfort in general

4. Germicidal Protection/Relieve Cold &

5. Reduce Smoking Odors in House

6. Reduce Pet Odors

7. Reduce Cooking Odors

8. Other

Where do you plan to use this Rabbit Air product?

12.

(Check all that apply)

1. Living Room

2. Bedroom

3. Child's Room

4. Family Room

5. Kitchen

Which group describes your annual family income?

13.

1. Under $29,999

2. $30,000-$39,999

3. $40,000-$49,999

4. $50,000-$59,999

5. $60,000-$74,999

6. $75,000-$99,999

Level of education: (check highest level completed)

14.

1. Completed High School

2. Completed College

3. Completed Graduate School

If this product was available in different color, which

15.

color would you prefer?

Are there other features that you would like to see on

16.

this product?

ZIP/Postal Code

Flu Symptoms.

Country

6. Office

7. Hallway

8. Bathroom

9. Home workshop area

10. Other

7. $100,000-$124,999

8. $125,000-$149,999

9. $150,000-$174,999

10. $175,000-$199,999

11. $200,000-$249,999

12. $250,000 & over

Rabbit Air

www.RabbitAir.com

Ultra Quiet Air Purifier

Please do not send products or other correspondences to this address

WARRANTY REGISTRATION FOR

RETURN THIS CARD NOW FOR:

Product Protection

With the information you provide we can confirm the date of purchase of your product. This confirmation is of benefit to you, especially if your original proof of purchase is lost.

Rabbit Air

201 West Garvey Ave., Suite 102-168

Monterey Park CA 91754-7418

Ultra Quiet Air Purifier

First-Class

Postage

Required

Post Office will

not deliver

without proper

postage.

Proof of Ownership

Your model number, serial number, and other information will be kept in our files. Please complete and return this registration within 30 days at purchase in order to receive

your 5 year Limited Warranty.

Or register online at: www.RabbitAir.com

Please fold and seal with tape before mailing. Do not staple.

Rabbit Air SPA-421A, SPA-582A User's Guide

Specifications and Main Features

Frequently Asked Questions

User Manual