Ultra Quiet Air Purifier
Hello!
Owner’s
manual
Models:
24/7 customer care
SPA-700A
SPA-780A
For Questions: Call 888.866.8862
Visit us at www.rabbitair.com
Hello there!
General Safety Information
About Your MinusA2 Air Purifier
Caution: When using electrical appliances, observe the following basic
precautions to reduce the risk of fire, electric shock, and injury:
• Please read all tips and warnings before using your Rabbit Air® purifier.
Meet your brand new MinusA2®!
“
We hope that this stylish bundle of cleanliness is just what
you've been looking for. Be sure to get familiar with this
newest addition to your home, by exploring all of its fea-
tures in the enclosed booklet and on our website.
If you have any questions just give us a call, anytime.
We love to hear from you!
• Use only as directed by the Owner’s Manual.
• Please observe extreme caution when using the air purifier in close proximity
to children.
• Rabbit Air purifiers are for indoor use only.
• The Rabbit Air purifier is not intended for use in bathrooms, laundry areas, or
other damp indoor environments. Keep the Rabbit Air purifier away from water
at all times.
• Do not use the Rabbit Air purifier near fireplaces or in areas where flammable or
combustible products or vapors may be present.
”
• This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure they do not play with the appliance.
• This product complies with the maximum allowable concentration of ozone of
0.050 parts per million by volume (ppmv) in a 24-hour period. The Health
Canada Guideline 2010 recommends that the Maximum exposure limit, based
on an averaging time of 8 hours, is 0.020 ppmv or less when tested in a Sealed,
controlled room approximately 30 m³.
A childproof feature pauses air purifier operation when
1 2
the front panel is removed.
Electrical Safety Instructions
Operation Guidelines
• The Rabbit Air purifier is designed for use in a 120V outlet only.
• Turn off your Rabbit Air purifier before unplugging it from the power outlet.
• Unplug the Rabbit Air purifier from the power outlet when not in use and before
servicing or cleaning the unit.
• To reduce the risk of electric shock, the Rabbit Air purifier has a polarized plug,
which means it will fit into a polarized outlet only one way. If the plug does not fit
into the outlet, reverse the plug. If it still does not fit, contact qualified personnel
to install the proper outlet. Do not alter the plug in any way.
• To avoid electric shock, do not touch the air purifier or its power plug
with wet hands.
• Keep the electrical cord away from heated surfaces at all times.
• If the cord or plug appears damaged, return the unit immediately to an authorized service facility for examination and repair.
• Any attempts to repair the Rabbit Air purifier without written permission from
Rabbit Air will void the warranty and could cause serious personal injury to the
user and/or result in severe damage to the unit.
• Do not pull, carry, lift, or drag the Rabbit Air purifier by pulling its power cord.
Remove the power plug from its outlet by grasping the plug and pulling gently.
• Do not block the air intake or air outlet.
• Do not use the Rabbit Air purifier on or around hot surfaces.
• Do not use the Rabbit Air purifier in a room where it may come into contact with
steam.
• Do not operate the Rabbit Air purifier on its side.
• Do not install the Rabbit Air purifier in greasy or damp environments.
• Do not use detergent or soap to clean the Rabbit Air purifier.
• Do not operate the Rabbit Air purifier without filters.
• Do not wash and reuse the filters except for the washable Pre-Filter.
• When transporting the Rabbit Air purifier, always hold the handle on
the back of the unit.
Remote Control Tips
• When the Rabbit Air purifier is plugged into a power outlet, keep all fingers,
body parts, hair, jewelry, and loose clothing away from the openings.
• Inverter lighting equipment or electronic light fixtures may interfere
with remote control signals.
• Avoid storing the remote control in direct sunlight. Heat may interfere
with remote control signals.
Installation Guidelines
The Energy Star label and disclaimer:
• Avoid putting the Rabbit Air purifier in a place where the air intake or air
outlet could become clogged with dirt.
• Leave at least two feet of space between the air purifier’s intake, outlet,
and the wall.
The energy efficiency of this ENERGY STAR qualified model is measured based on a
3 4
ratio between the model’s CADR for dust and the electrical energy it consumes, or
CADR/Watt.
Meet your MinusA2
Front view
Back view
Handle
Mood Light
Air Intake
(Around all sides
of front panel)
Control Panel/
Display Panel
Particle Sensor
Light Sensor
Power Cord
Bracket Holder
Air Outlet
Remote control
Power
Air Quality Indicator
Odor Sensor
Speed
Mood Light
Lithium coin battery (3V)
CR 2025
Mode
Negative Ion
on/off
5 6
MODE
Filter
Reset
MOOD
LIGHT
Control Panel Indicator Lights
Turbo
High
Medium
Low
Silent
Replace
Filters
Pollen
Auto
Filter
Reset
MOOD
LIGHT
Ion
Ion
on/off
Sleep
Light Sensor
Air Quality
Indicator
Ion
on/off
Light Sensor
Air Quality
Odor Sensor
Sleep
Indicator
Turbo
High
Medium
Low
Silent
Replace
Filters
Pollen
Auto
Ion
Power
Press and hold the power button for two
seconds to turn the unit on or off.
Speed
There are five speeds. Operation speed
changes in the following order as you press
the speed button.
Silent > Low > Medium > High > Turbo
Mode and Filter Reset
This is a dual control button. When
pressed briefly, you can change the
mode of operation between Auto
Mode and Pollen Mode. When
pressed and held, the Replace Filters
Indicator will be reset.
Mood Light and Negative Ion Generator
This dual control button, when pressed
briefly, will turn the Mood Light on or off.
When pressed and held, the Negative Ion
Generator will turn on or off.
Turbo
High
Medium
Low
Silent
Pollen
Replace
Filters
Fan Speed Indicator
Indicates the fan speed of
the air purifier. The lowest
speed is Silent. The highest
speed is Turbo.
Pollen Mode Indicator
When Pollen Mode is selected, the
fan speed of the air purifier
changes automatically depending
on the readings of the air quality
sensors. The Mood Light shifts
color in the following pattern:
blue > purple > light purple > pink .
Filter Replacement Indicator
When this indicator lights up, it
is time to replace your filters.
Once the filters are replaced,
press and hold the Mode/Filter
Reset button to reset the
Replace Filters Indicator.
Mood Light
Auto
Ion
Sleep
Air Quality
Indicator
Auto Mode Indicator
When Auto Mode is selected, the
fan speed of the air purifier
changes automatically depending
on the readings of the air quality
sensors and light sensor. The
Mood Light is solid blue when the
unit is in Auto Mode.
Ion Indicator
This indicates that the
Negative Ion Generator is
operating.
Sleep Lighting Indicator
This indicates that the unit is
operating in Sleep Lighting.
Air Quality Indicator
This light indicates the current air
quality in the room. The color will
shift from blue > purple > light
purple > red, depending on the
amount of contaminants. Blue
represents good air quality, while
red represents poor air quality.
The Mood Light has four colors: blue,
purple, light purple and pink.
7 8
Meet the Filters
Let’s Begin - Initial Set Up
The MinusA2 Air Purifier is designed for residential use only.
To maintain the quality of the filters, they are packaged in plastic. Please
remove the filters from the plastic wrapping before using the unit.
Your customized filter will be packaged in plastic outside of the unit. Set the
filter aside for later installation (step 6).
Medium Filter
Pre-Filter tabs
BioGS™ HEPA
Filter
Pre-Filter
Customized
Filter
Charcoal Based
Activated Carbon
Filter
1. Remove the front panel by
lifting from the bottom
and pulling up.
2. Remove the filter case by
grasping the handles on
both sides and pulling
3. Pull the tabs on the
front of the Pre-Filter
to remove it.
forward. Lay the filter case
on a flat surface.
REPLACE
FILTERS
Filter
Reset
Ion
ION
on/off
4. Remove the white Medium Filter from the black frame to discard the plastic wrapping.
Return the filter to its frame.
ODOR SENSOR
Filter case
5. Remove HEPA Filter and discard plastic wrapping.
Front panel
9 10
Finishing up!
6. Remove the empty Customized Filter frame from the case. Locate the
Customized Filter set aside from earlier and remove it from its plastic wrapping.
Insert the filter into its frame. Make sure the front of the filter is facing up. See
Customized Filter chart, below, to identify the front of your filter.
7. Pull out the Activated
Carbon Filter and discard
plastic wrapping.
8. Return the filters to the filter case in the
following order from back to front:
Activated Carbon Filter,
Customized Filter,
BioGS HEPA Filter,
Medium Filter,
Pre-Filter.
(See diagram on page 9).
Know your Customized Filter!
Toxin Absorber Customized Filter:
Front color: Purple
Back color: Black
Pet Allergy Customized Filter:
Front color: Purple & Orange
Back color: Orange
Germ Defense Customized Filter:
Front color: Purple & Yellow
Back color: Yellow
9. Return filter case to the unit. Slide the
bottom of the case back into the unit (1),
then press the top in (2).
REPLACE
FILTERS
Filter
Reset
Ion
ION
BackFront
on/off
ODOR SENSOR
10. Reattach the front panel by
latching the top hooks, then
securing the bottom of the panel.
Odor Remover Customized Filter:
Front color: Black (coated material)
Back color: Black
11 12
Operation Modes
Auto Mode
Plug the unit into a 120V outlet.
Press the power button. The air purifier will start up
automatically in Auto Mode.
The Mood Light will be a solid blue.
The color of the Air Quality Indicator changes based on
the amount of impurities in the air, and the fan speed
adjusts accordingly.
Sleep Lighting will activate if the room is dark for 3
minutes.
Air Quality
Indicator
Mode Selection
(Pollen Mode or Auto Mode)
Plug the unit into a 120V outlet.
After turning on the unit, briefly press
the Mode/Filter Reset button to select
your desired mode of operation, Pollen
or Auto.
When turned off and reactivated,
the unit will start up in the same
mode of operation it was last in.
Pollen
Auto
Ion
Pollen
Auto
Pollen Mode
Filter Reset
Plug the unit into a 120V outlet.
Press the power button to activate the unit.
Briefly press the Mode/Filter Reset button to select Pollen Mode.
In Pollen Mode, the color of the Mood Light will shift: blue > purple > light
The Replace Filters Indicator will become illuminated when
it is time to change your filters. Once you have replaced
the filters, press and hold the Mode/Filter Reset button for
three seconds, or until the Replace Filters Indicator clears
itself.
Filter
Reset
purple > pink.
The color of the Air Quality Indicator changes based on the amount of impuri-
Sleep Lighting
with Light Sensor
ties in the air, and the fan speed adjusts accordingly.
Sleep Lighting will activate if the room is dark for 3 minutes. While the Mood
Light and Air Quality Indicator will switch off, the fan speed of the air purifier
will continue to change based on the amount of impurities in the air.
While the MinusA2 is operating, the Light Sensor will detect the
brightness of the room. If the room is dark, the MinusA2 will
automatically switch to Sleep Lighting after three minutes and the
Light Sensor
Sleep Lighting indicator will become illuminated.
Manual Speed Selection
When the unit is in Sleep Lighting, the Mood Light and Air Quality
Plug the unit into a 120V outlet.
Low
Silent
Press the power button, the air purifier will start up
automatically in Auto Mode.
Replace
Press the Speed button to change the speed manually.
Choose among five speeds, Silent, Low, Medium, High
and Turbo.
The Mood Light will be a solid blue.
13 14
Sleep Lighting will activate if the room is dark for 3
minutes.
Filters
Turbo
High
Medium
Low
Silent
Indicator will automatically turn off.
If the unit is operating in Auto Mode, the fan speed of the air
purifier will automatically change to silent, minimizing energy
consumption and noise. Sleep Lighting will not override the fan
speed if the MinusA2 is operating in one of its manual speeds or
Pollen Mode.
MODE
Pollen
Auto
Sleep
Pollen
Ion
Auto
Pollen
Ion
Auto
Changing the Sensitivity Level of the Sensors
You can adjust the sensitivity level of the air quality sensors. The sensors come
preset at a standard sensitivity level as a default.
Press and hold both the Speed and
Mode button for three seconds.
Air Quality
Filter
Indicator
High
Medium
Low
Replace
Filters
Pollen
Auto
The Air Quality Indicator and Auto Mode
Indicator will blink.
Press the Speed button to
choose the sensitivity level.
Replace Filters : Low sensitivity
Pollen Mode : Standard sensitivity
Auto Mode : High sensitivity
Replace
Filters
Pollen
Auto
Mood Light Operation
Mood Light not only changes colors, but it also indicates the current operation mode.
Mood Light Button
The Mood Light turns on automatically when the air
purifier is turned on. Briefly press the Mood Light
button to turn the Mood Light on and off, or use the
remote.
The color of the Mood Light corresponds to the current mode of operation.
Auto Mode: Blue
Pollen Mode: The color of the Mood Light will shift: blue > purple > light purple > pink.
Negative Ion Generator
MOOD
Press and hold the Mood Light & Ion on/off button for three seconds.
The Negative Ion Generator will switch on or off. The Ion Indicator Light
will become illuminated when the generator is on.
LIGHT
Ion
on/off
Ion
Press and hold the Speed and Mode
buttons for three seconds to save the
sensitivity level. If no action is taken for
ten seconds, the sensitivity level you last
selected is saved automatically.
MOOD
LIGHT
15 16
Cleaning and Maintenance
Always unplug the unit before cleaning.
Cleaning the Particle Sensor
Clean particle sensor every three to six months.
Clean the air inlet and outlet using a vacuum
cleaner or soft brush.
1. Open the particle sensor cover on
the right side of the unit (when
facing the unit).
2. Use a damp cotton swab to clean
and dry the lens, dust inlet and dust
outlet.
Cleaning the Air Intake and Outlet
1. Clean the air intake and outlet with a soft brush.
Caution: Be careful not to drop
the brush into the unit.
Cleaning the Front Panel
1. Remove the front panel from the unit and use a dry
cloth or soft brush to dust it off.
Use a damp cloth to remove stubborn
stains and dirty buildup if necessary.
Avoid commercial cleaning products.
Cleaning the Mood Light Lens
1. Remove the front panel from the unit and use
a dry cloth, soft brush, or cotton swab to dust
off the Mood Light lens on the back of the panel.
Use a damp cloth to remove stubborn
stains and dirty buildup if necessary.
Avoid commercial cleaning products.
outlet
dust outlet
dust inlet
air inlet
Cleaning the Unit Surface
The unit surface should be cleaned depending
on the air quality of the room.
1. Use a clean, dry cloth to wipe the external surfaces of the air purifier.
Use a damp cloth to remove stubborn stains and dirty buildup if
necessary. Avoid commercial cleaning products which may damage
the unit's surface.
Cleaning the Pre-filter
The Pre-Filter should be cleaned depending on the air
quality of the room.
• To clean the Pre-Filter - vacuum method:
1. Remove front panel from the air purifier.
2. Run a vacuum cleaner with a nozzle or brush attachment on low
power setting along the Pre-Filter to remove visible particles.
If vacuuming does not seem to sufficiently clean your Pre-Filter,
please follow the steps below to wash it.
• To clean the Pre-Filter - washing method:
1. Remove the Pre-Filter from the unit.
2. Fill the sink with lukewarm water and gently wash the Pre-Filter
under the water for 2-3 minutes or until it is completely clean.
3. Rinse the Pre-Filter with clean tap water.
4. Use a towel to remove any excess water from the Pre-Filter.
5. Allow the Pre-Filter to dry for 12-24 hours.
6. When the Pre-Filter is completely dry, place back into the air purifier.
17 18
Filter Cleaning and
Replacement Schedule*
Replacing the BioGS HEPA Filter
Discard the old HEPA Filter, do not reuse.
every 12 months
Filters
Pre-Filter
Medium
BioGS HEPA
Customized
Charcoal-based Activated Carbon
Filter Life
Washable
Every 12 Months
Every 12 Months
Every 12 Months
Every 12 Months
*Based on 24/7 operation
Cleaning
Every Month
Not Required
Not Required
Not Required
Not Required
Replacing your Filters
Always unplug the unit before cleaning/replacing the filters.
Depending on the amount of pollutants in your indoor environment,
the life span of the filters will vary.
Pre-filter
Do NOT discard the Pre-Filter. It is designed to be cleaned and reused.
The Pre-Filter does not need to be replaced.
1. Pull the tabs on the front of the Pre-Filter to remove it.
2. Put the Pre-Filter to one side while replacing the other filters.
1. Remove old HEPA Filter and discard.
2. Remove new filter from plastic wrapping.
3. Place new HEPA Filter in filter case.
Replacing the Customized Filter
Do NOT discard the filter holder. Discard the old Customized
Filter, do not reuse.
1. Remove the old Customized Filter from the black frame and discard expired filter.
2. Take the new Customized Filter out of the plastic wrapping and place in the black frame.
3. Make sure the front of the Customized Filter is facing up. See Customized Filter
chart, (page 11) , to identify the front of your specific filter.
Replacing the Activated Carbon Filter
Discard the old Activated Carbon Filter, do not reuse.
every 12 months
every 12 months
1. Pull out the old Activated Carbon Filter and discard.
2. Remove the new Activated Carbon Filter from its
plastic wrapping, and place in the filter case.
Replacing the Medium Filter
Do NOT discard the filter frame. Discard the old Medium
Filter, do not reuse.
1. Remove the old Medium Filter from the black frame and discard the expired filter.
2. Open new Medium Filter and discard the plastic wrapping.
3. Secure the new filter in the black frame.
every 12 months
Return the filters to the filter case in the following order from back to front:
-Activated Carbon Filter,
-Customized Filter,
-BioGS HEPA Filter,
-Medium Filter,
-Pre-Filter.
(See diagram on page 9).
19 20
Wall-Mounting your MinusA2
(Optional)
Only use the approved Rabbit Air wall-mount kit to install the MinusA2 Air
Purifier on your wall. The MinusA2 Air Purifier is designed to be either free
standing or wall-mounted.
Wall-mount installation guidelines:
• Make sure the MinusA2 Air Purifier has at least two feet of clearance from the
ceiling and eight inches of clearance on either side.
• Be careful not to drop the front panel or filter case when replacing the filters.
• Do not pull on the power cord.
• Make sure the hanger screws have been securely driven into studs.
Don’t have a wall-mount kit? Want one? Order online at
www.rabbitair.com or over the phone at 888.866.8862
Disclaimer for installing wall-mounted objects
Do not attempt to install this product if you do not understand the
instructions. Contact a qualified contractor to install the mounting bracket and
call 1-888-866-8862 if you have any questions. You risk the possibility of
damaging the Air Purifier, damaging other property and personal injury if the
mounting bracket is not installed properly. Check to make sure there are no
missing or defective parts. Do not attempt to install the mounting bracket if
there are missing or defective parts. Contact Rabbit Air and replacement parts
will be shipped to you immediately. Rabbit Air is not liable for damage or injury
caused by incorrect mounting, incorrect assembly or incorrect usage.
• After installing the wall-mount bracket, make sure it is firmly in place before
putting the MinusA2 Air Purifier on it.
• Take care not to drill or screw into existing wiring in the wall while installing
the wall-mount bracket.
Correct installation is extremely essential, and falls outside the scope of
responsibility of Rabbit Air. Please consult a qualified contractor and/or
specialist supplier to install the mounting bracket. Maximum weight of air
purifier SPA-780A / SPA-700A: 8.8 kg/ 19.4 lbs.
21 22
Limited Warranty
Rabbit Air
Five (5) Year Limited Warranty
(For Rabbit Air Branded Products Only)
IMPORTANT: BY USING the BioGS 2.0 OR MinusA2 air purifiers (each, a “Rabbit Air Product”) YOU
ARE AGREEING TO BE BOUND BY THE TERMS OF THE RABBIT AIR FIVE (5) YEAR LIMITED
WARRANTY (“WARRANTY”) AS SET OUT BELOW. AS NOTED IN THE “YOUR RESPONSIBILITIES”
SECTION BELOW, RABBIT AIR RESERVES THE RIGHT NOT TO HONOR THIS WARRANTY IF IT HAS
NOT BEEN REGISTERED WITHIN NINETY (90) DAYS OF YOUR PURCHASE OF THE RABBIT AIR
PRODUCT. THIS WARRANTY APPLIES REGARDLESS OF WHETHER YOU PURCHASE A RABBIT AIR
PRODUCT FROM A RABBIT AIR AUTHORIZED RESELLER OR DIRECTLY FROM RABBIT AIR.
DO NOT USE YOUR RABBIT AIR PRODUCT UNTIL YOU HAVE READ THE TERMS OF THE WARRANTY. IF YOU DO NOT AGREE TO THE TERMS OF THE WARRANTY, DO NOT USE THE RABBIT AIR
PRODUCT AND RETURN IT WITHIN THE RETURN PERIOD STATED IN RABBIT AIR’S RETURN
POLICY (FOUND AT https://www.rabbitair.com/pages/why-rabbit-air#money-back) TO RABBIT
AIR OR TO THE AUTHORIZED RESELLER WHERE YOU PURCHASED IT FOR A REFUND. ThIS limited
warranty does not cover replacement filters, FILTER FRAMES, FILTER CASES, OR WALL MOUNT
BRACKETS.
HOW CONSUMER LAW RELATES TO THIS WARRANTY
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT
VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). OTHER THAN AS PERMITTED BY
LAW, RABBIT AIR DOES NOT EXCLUDE, LIMIT, OR SUSPEND OTHER RIGHTS YOU MAY HAVE,
INCLUDING THOSE THAT MAY ARISE FROM THE NONCONFORMITY OF A SALES CONTRACT. FOR
A FULL UNDERSTANDING OF YOUR RIGHTS YOU SHOULD CONSULT THE LAWS OF YOUR
COUNTRY, PROVINCE, OR STATE.
WARRANTY LIMITATIONS SUBJECT TO CONSUMER LAW
TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES, AND CONDITIONS, WHETHER
ORAL, WRITTEN, STATUTORY, EXPRESS, OR IMPLIED. LIKEWISE, TO THE EXTENT PERMITTED BY
LAW, RABBIT AIR DISCLAIMS ALL STATUTORY AND IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. INSOFAR AS SUCH WARRANTIES
CANNOT BE DISCLAIMED, RABBIT AIR LIMITS THE DURATION AND REMEDIES OF SUCH
WARRANTIES TO THE DURATION OF THIS EXPRESS WARRANTY AND, AT RABBIT AIR’S OPTION,
THE REPAIR OR REPLACEMENT SERVICES DESCRIBED BELOW. SOME STATES (OR COUNTRIES
AND PROVINCES) DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY (OR
CONDITION) MAY LAST, SO THE LIMITATION DESCRIBED ABOVE MAY NOT APPLY TO YOU.
WHAT IS COVERED BY THIS WARRANTY?
Kinetic Solutions, Inc., d/b/a “Rabbit Air”, located at 125 N Raymond Ave, Suite 308, Pasadena, CA
91103 (“Rabbit Air”), warrants Rabbit Air Products contained in the original packaging against
defects in materials and workmanship when used normally in accordance with Rabbit Air’s
published guidelines for a period of FIVE (5) YEARS from the date of original retail purchase by
the end-user purchaser (“Warranty Period”). Rabbit Air’s published guidelines include, but are
not limited to, information contained in technical specifications, user manuals, and service
communications.
WHAT IS NOT COVERED BY THIS WARRANTY?
This Warranty does not apply to any non-Rabbit Air branded hardware products, even if
packaged or sold with Rabbit Air hardware. Manufacturers, suppliers, or publishers, other than
Rabbit Air, may provide their own warranties to you. Please contact them for further informa-
tion. Rabbit Air does not warrant that the operation of the Rabbit Air Product will be uninterrupted or error-free. Rabbit Air is not responsible for damage arising from failure to follow
instructions relating to the Rabbit Air Product’s use.
Additionally, this Warranty does not apply: (a) to replacement filters, filter frames, filter cases,
or wall mount brackets; (b) to consumable parts, such as batteries or protective coatings, that
are designed to diminish over time, unless failure has occurred due to a defect in materials or
workmanship; (c) to cosmetic damage, including, but not limited to, scratches, dents, and
broken plastic, unless such damage has occurred due to a defect in materials or workmanship;
(d) to damage caused by use with a third party component or product, including without
limitation any replacement air filters not manufactured by Rabbit Air; (e) to damage caused by
breakdowns, fluctuations, or interruptions in electric power or by connection to improper
power supply; (f) to damage caused by accident, abuse, misuse, fire, liquid contact,
earthquake, or other external force; (g) to damage caused by operating the Rabbit Air Product
outside Rabbit Air’s published guidelines; (h) to damage caused by service performed by
anyone who is not a representative of Rabbit Air; (i) to a Rabbit Air Product that has been
modified to alter functionality or capability without the written permission of Rabbit Air; (j) to
defects caused by normal wear and tear or otherwise due to the normal aging of the Rabbit
Air Product; (k) to Rabbit Air Products marked as “sample” or sold “as is”; (l) if any serial
number has been removed or defaced from the Rabbit Air Product; or (m) if Rabbit Air receives
information from relevant public authorities that a Rabbit Air Product has been stolen.
YOUR RESPONSIBILITIES
Rabbit Air tries to honor this warranty in all cases where it has information regarding your
purchase; however, Rabbit Air reserves the right not to honor this warranty if it has not been
registered within ninety (90) days of your purchase of the Rabbit Air Product. Accordingly, we
encourage you to complete the warranty registration form online at www.rabbitair.com/war-
ranty. This warranty extends only to the original purchasers who acquire new products from
Rabbit Air or its authorized resellers, or to anyone who receives a Rabbit Air Product as a gift,
provided we are able to verify who made the purchase. Before receiving warranty service,
Rabbit Air or its agents may require that you furnish proof of purchase details, respond to
questions designed to assist with diagnosing potential issues, and follow Rabbit Air’s
procedures for obtaining warranty service.
WARRANTY SERVICE DURING THE FIRST 90 DAYS
To submit a claim under this warranty, please contact Rabbit Air at 1-888-866-8862 or by e-mail
at CustomerService@rabbitair.com. When contacting Rabbit Air via telephone, other charges
may apply depending on your location.
If you submit a valid claim to Rabbit Air in accordance with this warranty within ninety (90)
days of your purchase of a Rabbit Air Product, Rabbit Air will replace the Rabbit Air Product
with the same model (or with your consent a Rabbit Air Product that has similar functionality).
For warranty claims within the first ninety (90) days, Rabbit Air offers free shipping both ways
within the forty-eight (48) contiguous United States, and free shipping one way to Canada,
Hawaii, Alaska, Puerto Rico, Guam, the Virgin Islands, and APO, FPO or DPO addresses (you pay
for shipping to Rabbit Air, and we pay for shipping the replacement back to you).
23 24
WARRANTY SERVICE AFTER THE FIRST 90 DAYS
If you submit a valid claim to Rabbit Air in accordance with this warranty after ninety (90) days,
but during the Warranty Period, Rabbit Air’s obligation and liability under this limited warranty is
limited to repairing (or, at the sole discretion of Rabbit Air, replacing) the Rabbit Air Product, if in
need of repair or deemed defective. When a Rabbit Air Product or part is replaced, any replace-
ment item becomes your property and the replaced or refunded item becomes Rabbit Air’s
property.
To obtain service under this warranty, please contact Rabbit Air at the phone number or e-mail
listed above. A Rabbit Air representative will help determine whether your Rabbit Air Product
requires service or needs replacing and, if it does, will inform you how Rabbit Air will provide
such service or replacement. In such cases, Rabbit Air may, at its sole discretion, offer free
shipping both ways within the forty-eight (48) contiguous United States, or free shipping one
way to Canada, Hawaii, and Alaska (you pay for shipping to Rabbit Air, and we pay for shipping
the repaired or replaced product back to you).
Please note that any repairs attempted or completed without Rabbit Air authorization will void
this warranty.
Rabbit Air reserves the right to change the method by which Rabbit Air may provide warranty
service to you, and your Rabbit Air Product’s eligibility to receive a particular method of service.
Service will be limited to the options available in the country where service is requested. Service
options, parts availability, and response times may vary according to country. If you seek service
in a country that is not the original country of purchase, you will comply with all applicable
import and export laws and regulations and be responsible for all custom duties, V.A.T. and other
associated taxes and charges.
LIMITATION OF LIABILITY
EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY
LAW, RABBIT AIR IS NOT RESPONSIBLE FOR INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF ANY RABBIT AIR PRODUCT OR ANY BREACH OF
WARRANTY OR CONDITION, UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO
LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR ANTICIPATED PROFITS (INCLUDING LOSS
OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS;
LOSS OF BUSINESS; LOSS OF OPPORTUNITY; LOSS OF GOODWILL; OR LOSS OF REPUTATION.
THE FOREGOING LIMITATION SHALL NOT APPLY TO DEATH OR PERSONAL INJURY CLAIMS, OR
ANY STATUTORY LIABILITY FOR INTENTIONAL AND GROSS NEGLIGENT ACTS AND/OR
OMISSIONS.
The Rabbit Air five-year warranty is a statement of
“
our confidence in the quality of our products and
an assurance that we stand behind that quality 100
percent of the time. Labor is included in our
warranty; when warranty work is
performed, Rabbit Air pays the bill.
”
Warranty
Register online at www.rabbitair.com/warranty
SOME STATES (COUNTRIES AND PROVINCES) DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
GENERAL
No Rabbit Air reseller, agent, or employee is authorized to make any modification, extension, or
addition to this Warranty. If any term is held to be illegal or unenforceable, the legality or
enforceability of the remaining terms shall not be affected or impaired. This Warranty is
governed by and construed under the laws of the State of California, and you hereby consent to
the exclusive jurisdiction of the state courts in Los Angeles County, California. Rabbit Air or its
successor in title is the warrantor under this Warranty. Any future claims regarding your Rabbit
Air Product are governed by this Warranty. However, Rabbit Air reserves the right, as a general
matter, to change its warranty policies. If you make any future purchases of Rabbit Air Products,
those products may be governed by different warranty policies.
ADDITIONAL INFORMATION
Visit www.rabbitair.com to learn more, or speak with a Rabbit Air Consultant at 1-888-866-8862,
24 hours a day.
25 26
Register your air purifier online now for:
• Product Protection
By registering your product and purchase information, we can confirm the date of
purchase to secure your warranty. This confirmation serves as security in the event
that your original proof of purchase is lost, or in case your unit needs any servicing
in the future.
• Proof of Ownership
Your model number, serial number, and other information will be kept in our files.
Please complete and return this registration within 90 days from purchase in order
to receive our 5-year limited warranty.
24/7 customer care
For Questions: Call 888.866.8862
Visit us at www.rabbitair.com
Loading...