Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS ZE2816STYLE NUMBER ZE2816K:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Crossbar
Green Ground Screw
Mounting Screw
Lock Washer
Hex Nut (for Mounting Screw)
Mounting Ball
6 Rod"
12 Rod"
Flat Washer
Rubber Washer
Hex Nut (1/8IP)
Finial
Ceiling Canopy
ShadeAssembly
Diffuser
Stem
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 12-2008 Revised 2009-08-06
A
B
C
D
E
F
G
H
M
N
O
I
J
K
L
!
WARNINGS AND CAUTIONS
WARNING:
● Befo re beginning the in stal la tion, tu rn off el ectricity at th e circuit breaker box or the ma in fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safe ty. It is very i mportant t hat they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Di sconnect fixture from t he power source before replacing t he bulb(s), ma king sure the bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Befo re beginning in st allation of prod uct, make sure a ll parts are present. Comp ar e parts with p ac kage
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 20 30 minutes
● Tools R equi red for Assembly (not included): Flath ea d s crew driver Phillips scr ewdriver, plier s, electrical
tape, wire cutters, safety glasses &3, 60 Watt, Type A Medium Base Bulbs.
● He lp ful Tools (not included): Wire Strippers.
,
-
P
1 OF 3
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
.
a Determine the Rods to be assembled according to your
desired hanging height.
.
b Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Shade Assembly
together as shown. Tighten until snug.
6” Rod
12” Rod
Coupling
STYLE NUMBER ZE2816K:
6” Rod
12” Rod
Supply Wires with
Ground Wire
STEP 2:
.
a Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
.
b Thread the Swivel onto the top end of the Upper Rod and
hand tighten until snug.
STEP 3:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure
the position of the Mounting Screws by tightening the Hex
Nuts against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
.
Shade
Assembly
Ceiling Canopy
Swivel
Supply Wire with
Ground Wire
Upper Rod
Mounting Screw
Crossbar
Hex Nut
Lock Washer
2 OF 3
Outlet Box
Outlet Box Screw
Page 3
INSTALLATION INSTRUCTIONS
STEP 4:
* ( ) .
Use Wire Connectors not supplied to connect the wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.
b Connect the House White Wire to the Fixture Supply Wire
( )
White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 5:
a Place the Ceiling Canopy over the Mounting Screws and
.
thread Mounting Balls onto the Mounting Screws to secure
it. Hand tighten until snug.
WHITE WIRE
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE
FROM HOUSE
STYLE NUMBER ZE2816K:
WHITE OR RIBBED
FROM FIXTURE
BLACKOR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
STEP 6:
(Refer to Fig.1)
a. Thread the beaded end of the Stem into the Coupling
underside of the Socket Cluster. Hand tighten until snug.
b. Pass the Diffuser, the Rubber Washer and the Flat Washer
over the end of the Stem in turn and secure with the Hex
Nut (1/8IP). Hand tighten gently until snug.
c. Thread the Finial onto the end of the stem and hand tighten
until snug.
(Refer to Fig.2)
d. Please make sure the Diffuser is under the Tabs in the
bottom of the Shade after Assembly.
Fig.1
ShadeAssembly
Diffuser
Flat Washer
Finial
Fig.2
Socket
Cluster
Coupling
Stem
Rubber Washer
Hex Nut (1/8IP)
Shade
Diffuser
STEP 7
.
a Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
:
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
3 OF 3
Tab
Loading...