Quoizel YU5149IB User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
,.
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
ASSEMBLY / INSTALLATION INSTRUCTIONS
1 Before beginning the installation carefully unpack and
.
identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit breaker
..
,.
3.Unfold SUPPORTARMSto proper locations. Thread theend
of NIPPLE into COUPLINGon the top centerofJUNCTION
BOX. Hand tighten untilsnug. Proceed to locateCENTER
COLUMN over top endof NIPPLE and secureitwith
KNURLED NUT. Tightenuntil snug.
4. Thread FINIAL onto the nippleon the bottom centerof
JUNCTION BOX and handtighten until snug. Proceedto
thread FIXTURE LOOP onto thenipple on the topendof
CENTER COLUMN and handtighten until snug.
,
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
CEILING CANOPY
CANOPY LOCK RING
FIXTURE LOOP
KNURLED NUT
CENTER COLUMN
LOCK WASHER B
FIXTURE CHAIN
QUICK LINK
FIXTURE SUPPLY
and GROUND WIRE
SOCKET COLLAR
TOOL(supplied)
SOCKET
COLLAR
SHADE
5)
(
.
For Canadian installations, pleaserefer to Page 2
Fasten the CROSSBAR tothe OUTLET BOX with
(2)OUTLET BOXSCREWS(not supplied). Proceed to
thread LOCKNUT A and LOCK WASHER A onto
the top end ofNIPPLE. ThreadNIPPLEinto the center of
CROSSBAR. Locate the LOCK NUTB onto the bottom end
of the NIPPLE. Tighten LOCK NUT Aagainst CROSSBAR
with plier until snug.
6. Locate the FIXTURECHAIN and determine desired
hanging height of fixture.Adjust chain byremoving links if
needed. Please note thatdepending on chain material
thickness, you might berequired to use chain pliersto
spread links open. Proceed toattach the QUICK LINKonto
one end of chainand FIXTURE LOOP, attached to top of
fixture. Pass thefixture wires through FIXTURECHAIN
alternating links. Proceed to passthe fixture wires through
the following mounting componentsin this order:
1)CANOPY LOCK RING; 2)CEILING CANOPY
3 CANOPY CHAIN LOOP 4 LOCK WASHER B
))
and LOCK NUT B 5 NIPPLE 6 LOCK NUT A and
LOCK WASHER A
7. (2 people recommended forthe
Making the connections:
;) ;)
.
;
remaining steps)
Position the fixture underthe ceiling mounted outletbox.
Pass LOCK WASHER B overtheNIPPLE. Thread
CANOPY CHAIN LOOP onto NIPPLE.ThreadLOCK NUTB
down the NIPPLE, againstthe CANOPY CHAIN LOOP and
snug with pliers. Pass the wires through theNIPPLE.Take
up wire slack andtrim wires so thatapprox.6” will remain
inside outlet box. Proceed toattach the top oftheFIXTURE
CHAIN to the bottomof the CANOPY CHAIN LOOP. Using
wire connectors (not supplied)connect the HOUSE
GROUND WIRE to the FIXTURE GROUND WIRE
;
connect the HOUSE WHITEWIRE to the FIXTURE
SUPPLY WIRE (WHITE orRIBBEDSIDE); connect the
HOUSE BLACK (or RED)WIRE to the FIXTURESUPPLY
WIRE(BLACK or SMOOTH SIDE).Wrapeach connection
with approvedelectrical tape.
NIPPLE
COUPLING
JUNCTION BOX
FINIAL
SUPPORTARM
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
SHADE
HOLDER
SOCKET
8.With the proper connectionsmade, proceed to pushthe
CEILING CANOPY upward over theOUTLETBOX. Be sure
that all wires arecarefully tucked into theOUTLETBOX
cavity. Secure canopyagainstceiling by threading
CANOPY LOCK RING onto theCANOPYLOOP. Tighten
until snug.
9 Position SHADE HOLDER andSHADE over the SOCKET.
.
Use SOCKET COLLAR TOOL(supplied), thread SOCKET
COLLAR onto SOCKET and handtighten until snug to
secure them.
10.Install bulbs referring tofixture markings and/or labelsfor
maximum wattage.
11. Restore powertothe installation point ON. Retain this
sheet for future reference.
IS YU5149
-
Revised 2008 01 28
Page1of3
--
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTALLATION INSTRUCTIONS:
FOR FIXTURES OVER 25 LBS. (Canada Only)
(
Please use the information outlined in this sheet for the ceiling
installation part of your fixture assembly.
COTTER
PIN
HOUSE SUPPLY
and GROUND
WIRES
FIGURE 1.
3/8-18 NIPPLE, LOCK
WASHER AND
HEX NUT (INCLUDED)
HOLE DRILLED
INSIDE OUTLET
BOX
OUTLET BOX
SET SCREWS
COUPLING
LOCK WASHER A
Quoizel recommends a licensed electrician or contractor be
consulted for this installation.
1. Before installing fixture, carefully unpack and identify all parts
referring to illustration FIGURE 1. Be sure the power to the
installation point is OFF .
2.
(Refer to Figure 2, page 3) This weight of this fixture will require
at circuit breaker
a means of support independent of the OUTLET BOX. This
fixture must b supported by 3/8-18 NPSM NIPPLE(supplied)
e
Th NIPPLE should be positioned so that 3/4“ protrudes into
e
the OUTLET BOX cavity. Note: the opposite end of the NIPPLE
must be attached to a structural or bridging member of
sufficient strength to support the fixture weight. A COTTER PIN
has been included and should be installed into the top of
NIPPLE, above HEX NUT for added safety. A clearance hole
must be drilled on the inside top center of the OUTLET BOX.
Please refer to Figure 2, page 3 for detailed illustration. We
recommend the consultation of a licensed electrician or
contractor due to the complexity of this installation.
3. With the NIPPLE properly situated, locate COUPLING and proceed
to thread onto the end of the NIPPLE protruding into the OUTLET
BOX. Thread COUPLING onto pipe until tight. Tighten the top SET
SCREW with pliers to secure COUPLING to NIPPLE.
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE CHAIN
CEILING
CANOPY
FIXTURE SUPPLY
WIRE
4.
Making the connections:
the rest of this installation)
(Quoizel recommends (2) people for
Proceed to unravel the FIXTURE
SUPPLY and GROUND WIRES. Attach one end of the FIXTURE
LOOP at the top of FIXTURE. Please note that depending on chain
material thickness, you might be required to use chain pliers to
spread chain links open. Proceed to pass the FIXTURE SUPPLY
and GROUND WIRES through the chain, alternating links. Proceed
the pass the wires through the following mounting components in
this order: 1) CANOPY LOCK RING 2) CEILING CANOPY
;
Position the fixture under the OUTLET BOX. Locate the
.
CANOPY
CHAIN LOOP; LOCK WASHER B and LOCKNUT B;
NIPPLE ; LOCK NUT A and LOCK WASHER A. Thread
LOCK NUT A onto top end of NIPPLE. Pass LOCK WASHER A over
top end of NIPPLE. Thread LOCK NUT B onto the end of NIPPLE.
Pass LOCK WASHER B over end of NIPPLE. Thread the CANOPY
CHAIN LOOP onto the end of NIPPLE. Thread LOCK NUT B down
NIPPLE and snug against top of CANOPY CHAIN LOOP with pliers.
Pass wires through the bottom center CANOPY CHAIN LOOP
through NIPPLE. Pass
fixture wires through the bottom center of
the COUPLING. Pull wires through the wire way hole on side of
COUPLING.
Take up wire slack and trim wires so that approx. 6” will
remain inside outlet box.
Proceed to thread the NIPPLE into the bottom center of the
COUPLING until tight. Tighten the LOWER SET SCREW. Proceed
to thread LOCK NUT A and LOCK WASHER A up NIPPLE until
seated against the bottom of the COUPLING. Tighten until snug
with pliers. Attach the top of the FIXTURE CHAIN to the CANOPY
CHAIN LOOP.
Using wire connectors (not supplied),
GROUND WIRE to HOUSE GROUND WIRE
connect the FIXTURE
connect the HOUSE
;
WHITE WIRE to the FIXTURE SUPPLY WIRE (WHITE or RIBBED
SIDE); connect the HOUSE BLACK (or RED)WIRE to the FIXTURE
SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap
each
connection with approved electrical tape.
5. With the proper connections made roceed to push the CEILING
p
CANOPY upward over the OUTLET BOX. Be sure that all wires are
carefully tucked into the OUTLET BOX cavity. Secure canopy
against ceiling by threading CANOPY LOCK RING onto the
CANOPY LOOP. Tighten until snug.
CHAIN
CANOPY LOCK
RING
6. Refer back to Page 1, Step 9 and finish installation.
IS YU5149
-
Revised 2008 01 28
Page2of3
--
Loading...