Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-WV1716
STYLE NUMBER: WV1716BN
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
DESCRIPTION
Green Ground Screw
Mounting Screw
Small Lock Washer
Small Hex Nut
Mounting Ball
Lock Screw
Rubber Washer
Finial
Socket Assembly
Stem with Hex Nut
Shade
Diffuser
QUANTITY
1pc
1pc
2pcs
2pcs
2pcs
2pcs
3pcs
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 08-2010 REVISED 2010-10-29
A
B
C
D
E
F
G
H
I
J
K
L
M
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (3) 100W A19 medium base bulbs
● Helpful Tools (not included): Wire strippers.
1OF3
.
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a. Screw one end of the Stem with Hex Nut into the hex
coupling underside of the Socket Cluster. Using pliers,
thread the Hex Nut against the hex coupling and handtighten until snug.
STEP 2:
a. Lift the Shade over the Stem with Hex Nut, attach the
Tabs in it to the ends of the Side Arms. Thread the Lock
Screws into the end of the Side Arms and hand-tighten
until snug to secure the Shade.
STYLE NUMBER: WV1716BN
Socket Cluster
Stem with Hex Nut
Side Arm
STEP 3:
a. Place the Diffuser and the Rubber Washer over the end
of the Stem. The Diffuser should attach to the Studs in
the bottom edge of the Shade. Secure by threading the
Finial onto the Stem. Hand-tighten until snug.
Stem with
Hex Nut
Tab
Lock
Screw
Shade
Shade
Stud
Stem with Hex Nut
2OF3
Rubber Washer
Finial
Diffuser
Page 3
INSTALLATION INSTRUCTIONS
STYLE NUMBER: WV1716BN
STEP 4:
a. Screw the Mounting Screws into the Crossbar, place
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as
shown. Secure the position of the Mounting Screws by
tightening the Hex Nuts against the Crossbar.
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws.
STEP 5:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
Mounting Screw
Outlet Box
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
Crossbar
Hex Nut
Lock Washer
Outlet Box Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
STEP 6:
a. Place the Ceiling Canopy over the Mounting Screws
and secure with Mounting Balls. Hand-tighten until
snug .
STEP 7:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
3OF3
Loading...