6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
,.
Tools Required: Flatheadscrewdriver, Phillipsscrewdriver, pliers,wirecutters, wire
strippers,electricaltape,safety glasses.
BulbRecommended: (6) G9XenonClearBulbs (supplied), 0WMaximum4
EstimatedAssemblyTime: 30-45minutes
Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Assembly Instruction Sheet #IS-VLA2820C
For Style VLA2820C
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering June result.
Do not touch the bulb with bare hands use a cloth or glove.
Package Contents
Part
A Crossbar
B
C
D
E
F
G
H
Description
Mounting Screw
Fixture Body
G9 Xenon Clear Bulb
Allen Wrench
Screw
Trim G
Trim H
Quantity
1pc.
2 pcs.
1pc.
6 pcs.
1pc.
20 pcs.
10 pcs.
10 pcs.
A
B
C
E
F
G
D
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of4
H
August2014
VLA2820C
FINISH: POLISHED CHROME
A
A
104”
9.5”
1”
4.5” Dia.
2
3
20” Dia.
(6) 40W
G9 Xenon Clear
Bulbs
NO.
1
Maximum
(Supplied)
PART NUMBER
I1202SC
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BULB 40W XENON G9 CLEAR
1
REQ.
6
2
3
G3769CR
G3770CR
CRYSTAL BEAD W/ METAL FRAME SET 9"L PART "A"
CRYSTAL BEAD W/ METAL FRAME SET 9.75"L PART "B"
2of4
10
10
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-VLA2820C
For Style VLA2820C
STEP 1 Adjust the Fixture Body-
A. Push the Button and pull the Wire Rope to adjust the
length of Wire Rope to achieve your desired fixture
height. Then adjust the Wire Clasp A touch the Nipple in
the Canopy, secure by using thread
Allen Wrench (E)
the Inner Hexagon Screw into the Wire Clasp A, tighten
until sung for each wire rope.
B. Remove the Screw to open the Wire Clasp B.
adjust the
length of Wire to achieve your desired fixture height.
Secure by reinstalling the Screw, loosen Clasp B prior
to Step A if necessary.
STEP 2 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
STEP 3 Make Wire Connections-
Screw
Wire
Clasp B
Button
Wire Rope
Outlet Box
Screw
Wire
Clasp A
Inner Hexagon
Screw
Allen
Wrench
Nipple
Wire
Outlet
Box
Crossbar
Figure 1
Figure 2
Mounting
Hole
A. Use standard wire connectors to make all wire connections. (Connectors are not included with fixture.) Strip
and prepare wire ends according to instructions supplied with connectors.
B. If the electrical wire is going to be cut shorter than provided you will need to identify the "L" line wire and the "N"
wire before you cut the excess wire off. One is labeled N and the other labeled L. The third wire has a green
stripe on it. To do this strip back the clear wire covering the 3 fixture wires as far as you need to. This will
expose each fixture wire individually. Separate the "L" wire from the other two and re-label the wire near where
you want to make the cut. Be sure to mark the wire on the side of the fixture and not on the excess wire being cut
and removed. Do the same labeling with the "N" wire.
C. Connect White Supply Wire from the Outlet Box to Wire Labeled "N" from fixture.
D. Connect Black (or Red) Supply Wire from the Outlet Box to Wire Labeled "L” from fixture.
E. Connect Ground Wire from the Outlet Box to Green Striped Wire from fixture.
F. Twist connectors until wires are tightly joined together.
G. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet
Box.
White wire from supply Wire Labeled "N" from fixture
Black wire from supply
(or Red)
Ground wire from supply Green Striped wire from fixture
Figure 4
Wire Labeled "L" from fixture
Figure 3
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
3of4
August2014
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-VLA2820C
For Style VLA2820C
STEP 4 - Attach Ceiling Canopy to Crossbar
A. Thread Mounting Screws (B) into Mounting Holes on the
Crossbar (A). Leave proper length of Mounting Screws
(B) for Ceiling Canopy installation.
Pass the Gaps on the Ceiling Canopy over the
B.
Mounting Screw (B) and then rotate the Ceiling Canopy.
Do not free your hands until the Ceiling Canopy is
seated onto the Mounting Screws (B).
STEP 5 - Install Bulb
A. This fixture uses G9 Xenon Clear Bulbs (D). Maximum
40 watts.
B. Insert bulb and seat properly into place.
IMPORTANT:
a cloth or glove.
Do not touch the bulb with bare hands use
Figure 5
Crossbar
Mounting
Screw
Gap
Ceiling
Canopy
Figure 6
Socket
Bulb
STEP 6 Install Trims to Fixture-
A. Line up the Hole on Trim G with a hole on the
Fixture Body (C) and secure with Screw (F). Line
up the adjacent hole in Fixture Body (C) with
TrimHandsecurewithScrew(F),too.
B. Alternate Trim G and Trim H for each hole in the
Fixture Body (C).
Your fixture is now assembled and ready to use.
Enjoy!
Fixture Body
Screw
Figure 7
Trim G
Trim H
CAUTION FOR BULB REPLACING
A. When replace bulb, turn off power and allow lamp to cool. For safety purpose, wear gloves and eye protection.
B. If bulb is scratched or cracked, DO NOT use the lamp to avoid breakage during use or installation.
C. Use only in fixtures rated for lamps wattage and voltage.
D. Prevent the bulb from contacting liquid or combustible materials.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc. August2014
or visit us on-line at www.quoizel.com
4of4
Loading...