Assembly Instruction Sheet #IS-UST5003WT
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
,.
For Style UST5003WT
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended:
13WCFL, and (1) MR16 withGU10Base Bulb, 50W Maximum.
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
(3)Medium Base Decorative Filament 60W(supplied),Maximum 100W,Alternate bulb (3)
30-45minutes
Package Contents
Fixture Loop
A
x1
Small Lock Screw
B
x9
Large Lock
Screw
C
x3
MR16 Bulb
D
x1
Edison Bulb
E
x3
STEP 1 Adjust Fixture Assembly-
A. Unfold support arms on fixture
assembly to proper locations.
STEP 2 Install Ring and Fixture Loop-
A. Attach the Ring (I) to the support arms and
allign the holes on the Ring (I) to the
Mounting Holes on the support arms. Secure
it with the Large Lock Screws (C) and hand
tighten until snug.
B. Thread the Fixture Loop (A) onto the nipple
on the top end of the Socket Assembly (F).
Hand tighten until snug.
Figure 2
I
F
Socket Assembly
G
x1
H
Ring
I
x1
Shade
x3
Plastic
Suction
Tool
x1
Figure 1
A
F
Mounting
Hole
QUOIZEL
R
Crossbar
AA
x1
Lock Washer
BB
x2
Hex Nut
CC
x2
Nipple
DD
x1
Canopy
EE
Chain Loop
x1
STEP 3 Install Crossbar-
A. Attach the Crossbar (AA) to
the Outlet Box with the head
of the Green Ground Screw
facing you. Secure it with
Outlet Box Screws (not
included) Tighten until snug
STEP 4 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten
until snug.
B. Thread another Hex Nut (CC) to the
middle of the Nipple (DD). Place another
Lock Washer (BB) over the Nipple (DD)
and then thread the Nipple (DD) into the
Crossbar (AA) until the Nipple (DD) is
about 0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from
the Canopy Chain Loop (EE). Place the
Ceiling Canopy (II) over the Canopy
Chain Loop (EE) against the ceiling to
determine the correct position of the
C
Nipple (DD). Thread the Canopy Lock
Ring onto the Canopy Chain Loop (EE).
..
Figure 3
Hardware Contents
FF
GG
HH
II
Green Ground Screw
BB
AA
CC
EE
Figure 4
Canopy Lock Ring
x1
Fixture Chain
x1
Quick Link
x2
Ceiling Canopy
x1
Outlet Box
AA
Outlet Box
Screw (not
included)
Step B
CC
DD
BB
Step A
II
FF
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of3
February2014
Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to rest
against the ceiling when held in place by the Canopy Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
the links if needed.
*
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop (A) and
the Canopy Chain Loop (EE), pull the supply wires through the
Fixture Chain (GG) alternating links.After the wires are through the
Fixture Chain (GG), pull the Supply Wires and the Ground Wire
through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in
order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A) with
one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up And
Attach the other end of the Fixture Chain (GG) onto the Canopy
Chain Loop (EE) with another Quick Link (HH). The fixture will now
hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).
D. Feed the Supply Wires and Ground Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until
tight.
Suggested chain length for Ceiling height :
8’ ceiling : use 8 links of chain and 2 quick links
9’ ceiling : use 17 links of chain and 2 quick links
10’ ceiling : use 25 links of chain and 2 quick links
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 5
STEP 6 Install Shade and Bulbs-
A. Place the Shade (F) onto the Shade Holder and secure with Small
Lock Screws (B). Hand tighten until snug.
B. This fixture uses standard bulbs 60W (supplied) with standard screw
base. Maximum 100 watts. Insert bulb and screw snugly into place.
C. This fixture uses a MR16 bulb 50W (supplied) with gu10 base. Put
the Plastic Suction Tool (H) onto the MR16-GU10 Bulb. Install the
Bulb into the Socket Base by aligning the pins on the MR-16 Bulb
with the keyholes in the Socket Base. Once they are aligned, gently
push the Bulb into the keyholes and twist the Bulb to lock it in place.
And then remove the Plastic Suction Tool (H) from the MR16-GU10
Bulb.
Supply Wires
and Ground Wire
GG
DD
HH
HH
FF
EE
A
II
Figure 4
Your fixture is now assembled and ready to use. Enjoy!
Figure 6
D
GU10 Socket
H
E
B
F
Socket
Shade Holder
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of3
February2014