Quoizel UST1716WT User Manual
Assembly Instruction Sheet #IS-UST1716WT
For Style UST1716WT
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flathead screwdriver,Phillips screwdriver, pliers, wire cutters,wire strippers, electrical tape,
safetyglasses.
BulbRecommended:
13WCFL
EstimatedAssembly Time:
Preparation:
belowto be sure allparts are present. Ifany parts are missingor damaged, do notattempt to assemble, install,or
operatethe fixture. Contact customerservice for replacement parts.
Identifyand inspect all partsbefore beginning installation. Checkpackage content list anddiagrams
(3)Medium Base Decorative Filament60W (supplied), Maximum 100W,Alternatebulb (3)
30-45minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hex Nut
A
x1
Lock Washer
B
x1
Flat Washer
C
x1
Shade with Sockets
H
x1
Hardware Contents
Crossbar Assembly
x1
AA
Nipple with
Hex Nuts
G
x1
Check Ring
E
x1
Spacer Tube
F
x1
Edison Bulb
I
x3
D
Ceiling
Canopy
x1
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the
Crossbar Assembly (AA) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box Screws
(not included)
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
Remove mounting balls from the Crossbar Assembly (AA). Fit the
A.
Ceiling Canopy A to the
mounting balls. Note: The ( ) should be snug
against the and the mounting balls. If not, adjust the length of
the nipple on the Crossbar
Assembly (AA) by unscrewing
the preassembled hex nut and
lock washer and then screwing
the mounting screws in or out
of the crossbar until the correct
length is achieved. Once the
Ceiling Canopy (A) is secure,
remove the mounting ball and
Ceiling Canopy (A) and
proceed to Step 4.
STEP 4 Wire Connections-
( ) Crossbar Assembly (AA) and secure with
Ceiling Canopy A
ceiling
A
Figure 2
Outlet
Box
AA
Supply Wires
with Ground Wire
AA
Hex Nut and
Lock Washer
Mounting Screw
Mounting Ball
Figure 3
STEP 1 Assemble the Ceiling Canopy,
A. Thread one end of the Nipple with Hex Nuts
B. Place the Spacer Tube (F), the Check Ring
-
Spacer Tube and Shade with
Sockets
(G) into the Hex Coupling on the top center of
the Shade with Sockets (H). By using pliers,
thread one Hex Nut against the hex coupling
and hand tighten until snug.
(E), the Ceiling Canopy (D), the Flat Washer
(C) and the Lock Washer (B) over
the top end of the Nipple (G) in
turn. Secure them with the Hex Nut
(A) and hand tighten until snug.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 QuoizelInc.
H
Figure 1
B
E
Thank youfor purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
A
F
G
A. Use standard wire connectors (not included) to make all wire
C
D
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed Side Wire
from fixture. Connect Black (or Red) Supply Wire from the Outlet
Box to Smooth Side Wire from Fixture. Connect Ground Wire from
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
1of2
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 5
May2014
the Outlet Box to Ground Wire from fixture.
C. Twist connectors until wires are tightly joined together.
D. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the Ceiling
Canopy (A) over the outlet box.
Align the holes in the Ceiling
Canopy (A) with the mounting
screws, then attach the Ceiling
Canopy (A) using the previously
removed mounting balls. Hand
tighten until snug.
UST1716WT
FINISH: WESTERN BRONZE
A
Figure 5
AA
Mounting
Screw
Mounting Ball
STEP 6 Install Bulb-
A. This fixture uses standard bulbs 60W (supplied) with standard
screw base. Maximum 100 watts. Insert bulb and screw snugly into
place.
Your fixture is now assembled and ready to use. Enjoy!
Bulb
Figure 6
5” Dia.
(3) Medium Base
Decorative Filament
60W bulbs (provided),
Maximum 100W.
PART NUMBER
NO.
1
16” Dia.
16.5” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
11. 5 ”
6”
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
May2014
Loading...