Quoizel UST1505WT User Manual

Assembly Instruction Sheet #IS-UST1505WT
For Style UST1505WT
Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445
Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com
ToolsRequired: Flathead screwdriver,Phillips screwdriver, pliers, wire cutters,wire strippers, electrical tape, safetyglasses.
BulbRecommended:
13WCFL
EstimatedAssembly Time: Preparation:
belowto be sure allparts are present. Ifany parts are missingor damaged, do notattempt to assemble, install,or operatethe fixture. Contact customerservice for replacement parts.
Identifyand inspect all partsbefore beginning installation. Checkpackage content list anddiagrams
(1)Medium Base Decorative Filament60W (supplied), Maximum 100W,Alternatebulb (1)
30-45minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Package Contents
Ceiling Canopy
A
x1
Socket
E
Assembly x1
STEP 1 Assemble the Rods and the Ceiling Canopy-
A. Determine the Rods (B/C/D) to be assembled to the Socket
Assembly (G) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C/D) and the Ceiling Canopy (A). Thread the Socket Assembly (E), the chosen Rods (B/C/D) and the Ceiling Canopy (A) together. Hand tighten until snug.
A
6” Rod
B
x2
12” Rod
C
x1
12” Rod with Nipple
D
x1
Hardware Contents
Crossbar Assembly
x1
AA
Edison Bulb
F
x1
B
B
Supply Wires
and Ground Wire
E
Figure 1
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the Crossbar Assembly (AA) to the Outlet Box with the head of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included). Tighten until snug.
Outlet Box Screws
(not included)
STEP 3 Fit Ceiling Canopy to Crossbar Assembly-
Remove mounting balls from the Crossbar Assembly (AA). Fit the
A.
Ceiling Canopy A to the mounting balls. Note: The ( ) should be snug
( ) Crossbar Assembly (AA) and secure with
Ceiling Canopy A
D
C
Figure 2
Supply Wires
with Ground Wire
Outlet Box
AA
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank youfor purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
May2014
UST1505WT
FINISH: WESTERN BRONZE
(1) Medium Base
Decorative Filament
60W bulb (provided),
Maximum 100W.
PART NUMBER
NO.
1
against the and the mounting balls. If length of the nipple on the Crossbar Assembly (AA) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (A) is secure, remove the mounting ball and Ceiling Canopy (A) and proceed to Step 5.
STEP 4 Wire Connections-
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed Side Wire
from fixture. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth Side Wire from Fixture. Connect Ground Wire from
the Outlet Box to Ground Wire from fixture. C. Twist connectors until wires are tightly joined together. D. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
ceiling
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
not, adjust the
A
Figure 3
AA
Hex Nut and Lock Washer
Mounting Screw
Mounting Ball
4.5” Dia.
2”
45.5”
OVERALL HEIGHT
(2) 6” AND (2) 12” RODS
INCLUDED
7.5”
6”
5” Dia.
5.5” Dia.
REQ.
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the
outlet box and position the Ceiling Canopy (A) over the outlet box. Align the holes in the Ceiling Canopy (A) with the mounting screws, then attach the Ceiling Canopy (A) using the previously removed mounting balls. Hand tighten until snug.
STEP 6 Install Bulb-
A. This fixture uses standard bulbs 60W
(supplied) with standard screw base. Maximum 100 watts. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to
use. Enjoy!
AA
Mounting
A
Figure 5
Screw
Mounting Ball
Figure 6
Bulb
White wire
from supply
Black wire from supply (or Red)
Ground wire
from supply
2014 QuoizelInc.
Ribbed side wire from fixture
Smooth side wire from fixture
Ground wire from fixture
Figure 4
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of2
May2014
Loading...