Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-TY628
STYLE NUMBER: TY628AN, TY628WT
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
DESCRIPTION
Green Ground Screw
Nipple
Hex Nut
Lock Washer
Big Lock Ball
Small Lock Ball
Shade
Socket Collar
Steel Collar
Ceiling Canopy
Medium Assembly
6” Rod
12” Rod
Socket Assembly
QUANTITY
1pc
1pc
1pc
1pc
1pc
1pc
2pcs
6pcs
6pcs
6pcs
1pc
1pc
4pcs
4pcs
1pc
ISSUED 07-2010 REVISED 2010-10-14
I
A
B
C
D
E
F
G
H
J
K
L
M
N
O
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required forAssembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (6) 100W A19 medium base bulbs
● Helpful Tools (not included): Wire strippers.
.
1OF5
Page 2
INSTALLATION INSTRUCTIONS
STEP 1:
a. Place the Medium Assembly over the Bolts on the
Socket Assembly. Secure by threading Small Lock
Balls onto the Bolts. Hand-tighten until snug.
STYLE NUMBER: TY628AN, TY628WT
Medium
Assembly
Small
Lock Ball
Socket Assembly
Bolt
STEP 2:
a. Take apart the Swivel from the Ceiling Canopy by
unscrewing the Hex Nuts and the Lock Washers.
Ceiling
Canopy
Hex Nut
Lock Washer
Ceiling
Canopy
Swivel
2OF5
Page 3
INSTALLATION INSTRUCTIONS
STYLE NUMBER: TY628AN, TY628WT
STEP 3:
a. Determine the Rods to be assembled according to your
desired hanging height.
b. Screw the chosen Rods, the Medium Assembly and the
Swivel together as shown. Hand-tighten until snug.
6” Rod
12” Rod
Swivel
6” Rod
12” Rod
Medium Assembly
STEP 4:
a. Place the Ceiling Canopy and the Lock Washer back
over the Swivel. Secure by threading the Hex Nut back
onto the Swivel. Tighten until snug.
STEP 5:
a. Secure the Crossbar to the Outlet Box with Outlet Box
Screws. Tighten until snug.
Hex Nut
Lock Washer
Ceiling Canopy
Swivel
Crossbar
3OF5
Outlet Box
Outlet Box Screw
Page 4
INSTALLATION INSTRUCTIONS
STEP 6:
Pliers is required on this step.
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar.
c. Using pliers, thread the Hex Nut against the Crossbar
and hand-tighten until snug.
STEP 7:
a. Locate the Ceiling Canopy onto the Crossbar and slip
the Button Stop on the end of Lanyard into the Slot on
the Crossbar as shown.
Crossbar
Crossbar
STYLE NUMBER: TY628AN, TY628WT
Lock Washer
Hex Nut
Nipple
Slot
Button Stop
Lanyard
STEP 8:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
Ceiling Canopy
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
4OF5
Page 5
INSTALLATION INSTRUCTIONS
STEP 9:
a. Pass the Ceiling Canopy over the end of the Nipple and
secure with the Big Lock Ball. Hand-tighten until snug.
STYLE NUMBER: TY628AN, TY628WT
STEP 10:
a. Place the Shade and the Steel Collar over the Socket.
Secure by threading the Socket Collar onto the Socket.
Hand-tighten until snug.
Nipple
Big Lock Ball
Socket Collar
Steel Collar
Shade
Ceiling Canopy
Socket
STEP 11:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5OF5
Loading...