6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-TY5005
STYLE NUMBER: TY5005AN, TY5005WT
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
DESCRIPTION
Green Ground Screw
Mounting Screw
Lock Washer
Small Hex Nut
Mounting Ball
Socket Assembly
6” Rod
12” Rod
Ceiling Canopy
Shade
Steel Collar
Socket Collar
QUANTITY
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
2pcs
2pcs
1pc
5pcs
5pcs
5pcs
ISSUED 07-2010 REVISED 2010-10-20
J
A
B
K
C
D
E
F
G
L
M
H
I
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
1OF5
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required forAssembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (5) 100W Type-A medium base bulbs
● Helpful Tools (not included): Wire strippers.
.
STYLE NUMBER: TY5005AN, TY5005WT
INSTALLATION INSTRUCTIONS
STEP 1:
a. Refer to the Bottom View, unfold the Support Arms to
proper locations.
Support Arm
Bottom View
Support Arm
2OF5
INSTALLATION INSTRUCTIONS
STEP 2:
a. Determine the Rods to be assembled according to your
desired hanging height.
b. Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Socket
Assembly together as shown. Hand-tighten until snug.
STYLE NUMBER: TY5005AN, TY5005WT
6” Rod
6” Rod
12” Rod
12” Rod
STEP 3:
a. Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
b. Thread the Swivel onto the top end of the Upper Rod.
Hand-tighten until snug.
Coupling
Supply Wires with
Ground Wire
Socket
Assembly
Ceiling Canopy
Swivel
Supply Wire with
Ground Wire
3OF5
Upper Rod
INSTALLATION INSTRUCTIONS
STYLE NUMBER: TY5005AN, TY5005WT
STEP 4:
a. Screw the Mounting Screws into the Crossbar place
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as
shown Secure the position of the Mounting Screws by
.
tightening the Hex Nuts against the Crossbar
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws
.
,
.
STEP 5:
a. Locate the Ceiling Canopy onto the Crossbar and slip
the Button Stop on the end of Lanyard into the Slot on
the Crossbar as shown.
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box
Outlet Box Screw
Crossbar
Slot
Button Stop
Lanyard
Ceiling Canopy
STEP 6:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
4OF5
INSTALLATION INSTRUCTIONS
STEP 7:
a. Place the Ceiling Canopy over the Mounting Screws
and secure with the Mounting Balls. Hand-tighten until
snug.
STEP 8:
a. Place the Shade and the Steel Collar over the Socket
as shown. Secure by threading the Socket Collar onto
the Socket. Hand-tighten until snug.
STYLE NUMBER: TY5005AN, TY5005WT
Outlet Box
Mounting
Screw
Ceiling
Canopy
Mounting Ball
Socket Collar
Steel Collar
Shade
STEP 9:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
Socket
5OF5
Loading...