6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-TY1716
STYLE NUMBER: TY1716AN, TY1716WT
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
DESCRIPTION
Green Ground Screw
Mounting Screw
Lock Washer
Small Hex Nut
Mounting Ball
Lock Screw
1/8IP Hex Nut
Socket Assembly
Ring
Shade
Center Stem Assembly
Flat Washer
Rubber Washer
Cap
Finial
QUANTITY
1pc
1pc
2pcs
2pcs
2pcs
2pcs
3pcs
1pc
1pc
1pc
1pc
1pc
2pcs
2pcs
1pc
1pc
ISSUED 07-2010 REVISED 2011-01-27
L
A
M
B
N
C
O
D
E
F
G
H
I
P
J
K
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
1OF4
PREPARATION
STYLE NUMBER: TY1716AN, TY1716WT
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required forAssembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (3) 100W Type-A medium base bulbs
.
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Attach the Connectors on the Ring to the bottom of the
Side Arms. Line up mounting holes on the Connectors
and holes on the Side Arms. Using screwdriver, thread
Lock Screws into the mounting holes on Connectors to
secure them together. Hand-tighten until snug.
Lock Screw
Ring
Socket Assembly
Side Arm
STEP 2:
a. Screw the Mounting Screws into the Crossbar place
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as
shown Secure the position of the Mounting Screws by
.
tightening the Hex Nuts against the Crossbar
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws
.
,
.
Connector
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box
Outlet Box Screw
2OF4
INSTALLATION INSTRUCTIONS
STEP 3:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
STEP 4:
a. Place the Ceiling Canopy over the Mounting Screws
and secure with the Mounting Balls. Hand-tighten until
snug.
STYLE NUMBER: TY1716AN, TY1716WT
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
Mounting
Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
Outlet Box
Ceiling
Canopy
STEP 5:
a. Screw the short nipple end of the Center Stem
Assembly into the Hex Coupling underside of the
Socket Cluster. Hand-tighten until snug.
Socket Cluster
Mounting Ball
Hex Coupling
Center Stem
Assembly
3OF4
INSTALLATION INSTRUCTIONS
STEP 6:
a. Pass the Flat Washers, the Rubber Washers and the
Shade over the end of the Center StemAssembly as
shown. Secure them by threading the 1/8 IP Hex Nut
onto the Center Stem. Hand-tighten until snug.
STYLE NUMBER: TY1716AN, TY1716WT
Center Stem
Assembly
STEP 7:
a. Place the Cap over the end of the Center Stem and
secure with the Finial B. Hand-tighten until snug.
Shade
Flat Washer
Flat Washer
Rubber Washer
Rubber Washer
1/8 IP Hex Nut
Center Stem
Cap
STEP 8:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
4OF4
Finial B
Loading...