Quoizel TRE9009K Assembly Instruction Sheet
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TRE9009K
For Style TRE9009K
Pleasegoto forproductcleaningtips.Gotothe selection.
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/16”
drillbit,centerpunch,hammer,drill and wrench.
LightSource:
EstimatedAssembly Time:
Preparation:
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
(1)A21 Medium Base bulb 150W Maximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Mounting Screw
A
x3
Lock Ball
B
x2
Fixture Hood
C
x1
Glass Panel
Fixture
D
Body
x1
I
STEP 1 Attach the Glass Panels, Curve
Panels and Glass Shade to Fixture Body
A. Insert one Glass Panel (F) into the cage of
B. Insert one Curve Panel (E) into the cage
C. Place the Glass Shade (I) and the Steel
-
the Fixture Body (D) first. Attach the
bottom edge of the Glass Panel (F) to slot
in one of the rest sides. And fold the Tabs
in the top edge of the cage to secure the
top edge of the Glass Panel (F). Repeat
the same process to install another Glass
Panel (F) to the opposite side of the cage.
of the Fixture Body (D). Attach the bottom
edge of the Curve Panel (E) to slot on one
narrow side of the cage. And fold the Tabs
in the top edge of the cage to secure the
top edge of the Curve Panel (E). Repeat
the same process to install another Curve
Panel (E) to another narrow side of the
cage.
Collar (G) over the socket as shown. By
using the Socket Collar Tool (J), thread
the Socket Collar (H) onto the socket and
hand tighten until snug to secure the
Glass Shade (I).
Figure 1
x2
Steel Collar
G
x1
Socket Collar
H
x1
Glass Shade
x1
H
E
F
J
Curve
Panel
x2
Socket
Collar Tool
x1
G
I
Tab
Socket
Slot
STEP 2 - Mark the Location for the 3 Mounting Holes
A. Place the light fixture onto the post and mark the location of the 3
mounting holes on the fixture fitter onto the post with the marking
pen.
Post
Lighting
Fixture
Fitter
Post
STEP 3 M C
EM H
A. Remove the light fixture. Using
E
STEP 4 Drill Holes-
F
A. Using the 1/16” bit and drill, drill a pilot hole completely through the
D
- arking the enter of
ach ounting ole
the center punch and hammer
marking the center of each
mounting hole location that is
marked with the marking pen.
post at each (3) locations marked in step 5 above.
Figure 4
Marking Pen
Mounting
Hole
Figure 2
Center Punch
1/16” bit and drill
Post
Hammer
Marking
Post
Fixture
Fitter
Post
Figure 3
2017 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
1of2
ReleasedDate:2017-01-05
STEP 5 - Wire Connections
TRE9009K
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
STEP 6 Attach the fixture
to the Post Mount
A. Place the fixture on the
-
post lining up the mounting
holes on the fixture fitter
with the holes on the post.
Use the Mounting Screws
(A) to attach the fixture to
the post.
Figure 5
Fixture
Fitter
White wire
from fixture
Black wire
from fixture
A
Ground wire
from fixture
Mounting
Hole
Post
Hole
Post
Lighting
FINISH: MYSTIC BLACK
8.5"
4" Dia.
7.75"
17.25"
7.75"
STEP 7 - Install the Bulb and
Fixture Hood
A. Insert the bulb onto socket and
screw snugly into place.
B. Pass the Fixture Hood (C) over the
bolts on the top edge of the Fixture
Body (D) and secure with Lock
Balls (B). Hand tighten until snug.
Your fixture is now assembled and
ready to use. Enjoy!
Figure 6
Bulb (not
supplied)
Figure 7
B
Bolt
D
Socket
C
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
2017 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
2of2
ReleasedDate:2017-01-05
Loading...