Quoizel TFST2822VB User Manual

Assembly Instruction Sheet #IS-TFST2822VB

For Style TFST2822VB

ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wirestrippers,electrical tape, safety glasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:

present.Ifany parts are missingordamaged, do not attempttoassemble, install, or operatethefixture. Contact customer serviceforreplacement
parts.

Identifyandinspect all parts beforebeginninginstallation. Check package contentlistand diagrams below tobesure all parts are

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

Care of Tiffany Style Shade

A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.

For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.

If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.

(4) bulbs100WMaximum, AlternateBulb(4) 23W CFL

MediumBase

20-30minutes

Package Contents

Fixture Loop

A

x1

Socket

B

Assembly
x1

Crossbar

AA

x1

Lock Washer

BB

x2

Hex Nut

CC

x2

Nipple

DD

x1

Side Arms

C

x4

D

E

F

Hardware Contents

Canopy Chain

EE

Loop
x1

Canopy Lock Ring

FF

x1

Fixture Chain

GG

x1

Quick Link

HH

x2

Ceiling Canopy

II

x1

Center
Stem
x1

Finial
x1

Shade
x1

STEP 1 Install Fixture Loop-

A. Thread the Fixture Loop (A) onto the

nipple on the top center of the Socket
Assembly (B). Hand tighten until snug.

Figure 1

STEP 2 Install Shade-

Quoizel recommends (2) people for this step.

A. Thread the hex nut end of the Center Stem

(D) into the hex coupling on the bottom center
of the Socket Assembly (B). Hand tighten until
snug.

B. Place the Shade (F) over the end of the

Center Stem (D). With one person hold the
Shade (F), another person attach one

end of the Side Arm (C) to the Loop at
the Socket Assembly (B) and attach
another ends of the SideArms (C) to
the Loops in the Shade (F).

C. Adjust the Knurled Nut on the Center

Stem (D) until it is flush to the Shade
(F). Thread the Finial (E) onto the end
of the Center Stem (D) to secure the
Shade (F). Hand tighten until snug.

Figure 2

A

B

D

E

B

Loop

C

Loop

F

2014 QuoizelInc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

1of3

August2014

STEP 3 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..

Outlet Box

hang safely. Close the chain loop at the Ceiling Canopy Loop (EE).
D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving

approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 6 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the

Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten

the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until

tight.

AA

Outlet Box Screw
(not included)

Green Ground Screw

Figure 3

STEP 4 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)
is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to
rest against the ceiling when held in place by the Canopy Lock Ring
(FF).

D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).

Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.

Suggested chain length for Ceiling height :

8’ ceiling : use 1 link of chain and 2 quick links

9’ ceiling : use 11 links of chain and 2 quick links

10’ ceiling : use 21 links of chain and 2 quick links

Supply Wires

and Ground Wire

GG

DD

EE

HH

FF

HH

A

II

AA

DD

BB

CC

EE

FF

CC

BB

Step B

Step A

II

Figure 4

STEP 5 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

the links if needed.

*

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop (A)

and the Canopy Chain Loop (EE), pull the supply wires through the
Fixture Chain (GG) alternating links.After the wires are through the
Fixture Chain (GG), pull the Supply Wires and the Ground Wire
through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in
order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A)

with one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up
And Attach the other end of the Fixture Chain (GG) onto the Canopy
Chain Loop (EE) with another Quick Link (HH). The fixture will now

Figure 5

STEP 6 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.

White wire

from supply

Black wire from
supply (or Red)

Ground wire

from supply

Ribbed side wire
from fixture

Smooth side wire
from fixture

Ground wire
from fixture

Figure 6

STEP 7 Install Bulb-

A. This fixture uses standard bulb with medium base . Maximum 100

watts.

B. Insert bulb and screw snugly into

place.

Your fixture is now assembled
and ready to use. Enjoy!

Bulb

Figure 7

2014 QuoizelInc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

2of3

August2014