Quoizel TFSM1818VB User Manual

Assembly Instruction Sheet #IS-TFSM1818VB

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Care of Tiffany Style Shade

A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.

For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.

If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or mineral oil applied directly to oxidized areas and the soldered area will return to like new.

For Style TFSM1818VB

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,

safetyglasses.

BulbRecommended: (3) MediumBase 100W Maximum,Alternatebulb (3) 23W CFL EstimatedAssembly Time:20-30minutes

Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams

belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer serviceforreplacement parts.

Package Contents

Ceiling Canopy

Lock Ball

6” Rod with Connector

6” Rod

STEP 1 Attach Socket Assembly

and Shade Together

A. Place Shade (I) over the nipple on

the top of SocketAssembly (J), secure with Knurled Nut (H). Hand tighten until sung.

B. Thread the LoopAssembly (G)

onto the nipple on the top of Socket Assembly (J). Hand tighten until sung.

12” Rod

6” Rod with Connector

Shade

Socket Assembly

Connector

Loop Assembly x2

Knurled Nut

Glass Panel x1

Figure 1

2.4mm 13Ga

QUOIZEL

GND

STEP 2 Attach panel to Shade-

A. Insert Glass Panels (L) into the

slot in the Shade (I) then fold the tabs to secure the Glass Panels (L).

STEP 3 Assemble Rods-

A. Determine the Rods (C/D/E/F) and

Connector (K) (Optional) to be assembled to the LoopAssembly (G) on top of Shade (L) according to your hanging height.

B. Pass Supply Wires and Ground Wire

through the chosen Rods ( Connector (K) (Optional) chosen Rods ( (Optional) Loop Assembly (G) on top of Shade ( )

C/D/E/F) and Connector (K)

and

I together. Hand tighten until

C/D/E/F) and

. Then thread the

snug.

C. Pass Supply Wires and Ground Wire

through Loop Assembly (G) and Ceiling Canopy (A). Then thread the Ceiling Canopy (A), LoopAssembly (G) and the Upper Rod together. Hand tighten until snug.

Hardware Contents

Crossbar Assembly x1

Figure 2

Figure 3

2014 Quoizel Inc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

1of2

August2014

Suggested rods for Ceiling height : 8’ ceiling : use (1) 12” rod with connector (F) and (1) connector (K) 9’ ceiling : use (1) 12” rod (E) and (1) 12” rods with connector (F) 10’ ceiling: use (1) 6” rod with connector (C), (1) 6” rod (D), (1) 12” rod (E) and (1) 12” rods with connector (F)

STEP 4 Install Crossbar-

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug

STEP 6 Attach Fixture Body to Mounting Screw-

A. Place the Backplate of the Fixture Body (A) over the Mounting

Screws and secure with Lock Ball (B). Hand tighten until snug.

Mounting Screw

Outlet Box

Outlet Box Screw (not included)

Figure 4

Green Ground Screw

STEP 5 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.

White wire

from supply

Black wire from supply (or Red)

Ground wire

from supply

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

Figure 5

TFSM1818VB

FINISH: VINTAGE BRONZE

STEP 7 Install Bulb-

A. This fixture uses standard bulb with

medium screw base. Maximum 100 watts.

B. Insert bulb and screw snugly into place.

Your fixture is now assembled and ready to use. Enjoy!

6” Sq.

1”

Figure 6

Figure 7

Socket

Bulb

2.4mm

13Ga

Base

Medium

Bulbs

(3) 100W

(Not Supplied)

2014 Quoizel Inc.

GND

QUOIZEL

(2) 6” AND 12” RODSAND 2 QUICK LINKS

PART NUMBER

NO.

G3879PA

G3878PA

9106EXVB

9112EXVB

REPLACEMENT PART

GLASS PANEL

6” ROD

12” ROD

REQ.

18” Sq.

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2of2

OVERALL HEIGHT INCLUDES

59.5”

13.5”

10”

August2014