Quoizel TFSM1615VB User Manual
Assembly Instruction Sheet #IS-TFSM1615VB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
,.
For Style TFSM1615VB
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (2) MediumBase 75W Maximum,Alternatebulb (2) 19W CFL
EstimatedAssembly Time:20-30minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Package Contents
Finial
Ceiling Canopy
A
x1
Nipple with
Hex Nut
B
x1
Shade
C
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to
the Outlet Box with the head of
the Green Ground Screw
facing you. Secure it with
Outlet Box Screws (not
included) Tighten until snug..
STEP 2 - Attach Nipple to Crossbar
A. Thread one Hex Nut (DD) onto the top end of the Nipple (BB).
B. Place one Lock Washer (CC) over the top end of the Nipple (BB) and
then thread the Nipple (BB) into the center lock hole of the Crossbar
(AA).
C. Using pliers, thread the Hex Nut (DD) against the Crossbar (AA) and
hand tighten until snug.
D. Thread the other Hex Nut (DD) onto the other end of the Nipple
(BB). Thread this Hex Nut (DD) on just enough so the inside surface
of the Ceiling Canopy (A) rests against it. * You may have to trial fit
the Ceiling Canopy (A) one more times to insure this distance also.
This Hex Nut (DD) is needed here to prevent you from crushing
down the center of the Ceiling Canopy (A).
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Green Ground Screw
D
x1
Outlet Box
AA
Outlet Box Screw
(not included)
Figure 1
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
Hardware Contents
Crossbar
AA
x1
Nipple
BB
x1
Lock Washer
CC
x2
AA
DD
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
1of2
CC
DD
BB
Hex Nut
DD
x2
Flat Washer
EE
x1
Hex Coupling
FF
x1
A
Figure 2
April2014
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 3
STEP 5 Install Nipple with Hex
-
Nut
A. Thread the hex nut end of the
Nipple with Hex Nut (B) to the
Hex Coupling (FF) underside of
the Ceiling Canopy (A). By using
pliers, thread the hex nut against
the Hex Coupling (FF) and hand
tighten until snug.
A
FF
B
Figure 5
STEP 4 Attach Ceiling Canopy-
A. Position the Ceiling Canopy (A) to the ceiling by passing the
Nipple (BB) through the center hole.
B. Slip on the Flat Washer (EE) and the Lock Washer (CC) and then
thread the Hex Coupling (FF) to the bottom end of the Nipple
(BB). Snug down assembly until the Ceiling Canopy (A) is flush
against the ceiling.
* Be sure that there are no trapped or pinched wires along the
edge of the Ceiling Canopy (A).
BB
A
EE
CC
FF
Figure 4
TFSM1615VB
FINISH: VINTAGE BRONZE
GND
STEP 6 - Install Bulb
A. standard bulb
This fixture uses
with a medium screw base
.
Maximum 75 watts.
B. Insert bulb and screw snugly
into place.
STEP 7 - Install Shade
A. Place the Shade (C) over the
end of the Nipple with Hex Nut
(B) and secure with the Finial
(D). Hand tighten until snug.
Your fixture is now assembled
and ready to use. Enjoy!
Socket
Bulb
Figure 7
Figure 6
B
C
D
2.4mm
(2) 75W
Base
(Not Supplied)
PART NUMBER
NO.
1
13Ga
Medium
Bulbs
QUOIZEL
R
5” 7.5”
14.5”Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
15”Dia.
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
April2014
Loading...