6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TFJD1718ML
For Style TFJD1718ML
ToolsRequired:Flatheadscrewdriver,Phillips screwdriver,pliers,wirecutters,wire
Quoizel, Inc.
strippers,electricaltape,safetyglasses.
6 Corporate Parkway
Goose Creek, SC
29445
BulbRecommended: (3) Medium Base 100W Maximum
EstimatedAssemblyTime:20-30 minutes
Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackage
Customer Service
Phone 631.273.2700
Fax 631.231.7102
contentlistanddiagramsbelowtobesureallpartsarepresent.Ifanypartsaremissing
ordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer
serviceforreplacementparts.
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
G
Package Contents
Part
Description
A Crossbar
B
C
D
E
F
G
H
J
K
L
M
N
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Fixture Body
Stem 4” L
Side Chain
Spacer
I
Check Ring
Shade
Cap
Finial
1/8P Hex Nut
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
1pc.
1pc.
3 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
2 pcs.
A
B
C
D
E
F
H
I
J
K
L
M
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
1of5
N
November2013
TFJD1718ML
FINISH: MALAGA
5.5” Dia.
GND
2.4mm
13Ga
QUOIZEL
R
13”
6”
1
18” Dia.
(3)100W Medium
Base Bulbs
(Not Supplied)
PART NUMBER
NO.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
1 G3596SH TIFFANY SHADE 18"D 1
2of5
REQ.
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TFJD1718ML
For Style TFJD1718ML
STEP 1 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Ceiling Canopy.
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex Nut
(D) onto the Mounting Screws (B). Hand tighten until
snug.
STEP 2 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Figure 1
Mounting Screw
Lock Washer
Ceiling
Canopy
Figure 2
Mounting
Hole
Crossbar
Hex Nut
Outlet
Box
Crossbar
Outlet Box
Screw
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
3of5
November2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TFJD1718ML
For Style TFJD1718ML
STEP 3 Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supply White wire from fixture
Figure 4
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Black wire from fixture
Figure 3
STEP 4 - Attach Ceiling Canopy to Mounting
Screw
A. Place the Ceiling Canopy on the top of the Fixture Body
(F) over the Mounting Screws (B) and secure with
Mounting Balls (E). Hand tighten until snug.
STEP 5 Attach Stem 4.5”L with Hex Nut-
A. Thread (G) into Coupling on the bottom of
Fixture Body (F). Hand tighten until snug.
Stem 4” L
Ceiling
Canopy
Fixture Body
Figure 5
Mounting
Screw
Mounting
Ball
Figure 6
Fixture Body
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2013 Quoizel Inc.
Coupling
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
4of5
Stem 4” L
November2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TFJD1718ML
For Style TFJD1718ML
STEP 6 Install Shade to fixture-
A. Place the Spacer (I), Check Ring (J) and the center hole
on the Shade (K) over the Stem 4” L(G). Thread the 1/8P
Hex Nut (N) onto the Stem 4”L (G) underside of the Shade
(K). Hand tighten until sung.
B. Attach the Loop on the end of the Side Chain (H) to the
Hook on the side of Canopy . Attach the Loop on the other
end of the Side Chain (H) to the Hook inside of the Shade
(K).
STEP 7 Attach the Cap and Finial to fixture-
A. on the
Thread the 1/8P Hex Nut (N) onto the Stem 4”L (G)
proper location, place the Cap (L) over the Stem 4”L (G),
secure with the Finial (M) Hand tighten until sung.
.
Canopy
Socket
Assembly
Stem 4”L
Spacer
Hook
Figure 7
Loop
Side Chain
Loop
Check Ring
Hook
Shade
1/8P Hex Nut
Figure 8
STEP 8 Install Bulb-
A. This fixture uses standard bulb with a standard screw base.
Maximum 100 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Shade
Shade 4”L
Socket
Bulb
Cap
1/8P Hex Nut
Finial
Figure 9
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
5of5
November2013
Loading...