Quoizel TFIK8802 User Manual

Assembly Instruction Sheet #IS-TFIK8802

For Style TFIK8802

ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver, pliers,wirecutters, wire strippers,electricaltape, safety glasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:

present.Ifany parts aremissingor damaged, donotattempt to assemble, install,oroperate the fixture.Contactcustomer service forreplacement
parts.

Fixturecanonly be mountedinthe direction indicated onpage 2.

Identifyandinspect all partsbeforebeginning installation. Check packagecontent list and diagramsbelowto be sureallparts are

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

(2) Base 0WMaximum,Candelabra 6 Candelabra

30-45minutes

Alternatebulb(2) 13W CFL .

Package Contents

Lock Ball

F

x2

Crossbar

A

x1

Nipple

B

x1

Lock Washer

C

x1

Hex Nut

D

x1

Mounting Ball

E

x1

STEP 1 Attach Nipple to Crossbar-

A. Secure the Crossbar (A) to the outlet box with outlet box screws

(not supplied). Tighten until snug.
B. Thread one Hex Nut (D) onto the top end of the Nipple (B).
C. Place one Lock Washer (C) over the top end of the Nipple (B) and

then thread the Nipple (B) into the center lock hole of the

Crossbar (A).
D. Using pliers, thread the Hex Nut (D) against the Crossbar (A) and

hand tighten until snug.

Outlet Box

STEP 2 Attach Shade to Socket Assembly-

A. Pass holes on the Bar and over the

bolts I and with Lock Balls (F).

on the Socket Assembly ( ) secure

A

C

D

the Small Lock Washers (G)

Small Lock Washer

G

x2

Shade

H

x1

I

Outlet Box
Screw (not
Supplied)

B

Socket Assembly
x1

Figure 1

Bolt

I

STEP 3 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.

White wire

from supply

Black wire from
supply (or Red)

Ground wire

from supply

STEP 4 Attach Fixture Body to Nipple-

A. Place the Backplate of the Socket

Assembly (I) over the Nipple (B) and
secure with the Mounting Ball (E).
Hand tighten until snug.

B. This fixture uses standard bulbs with a

standard screw base. Maximum 60
watts. Insert bulb and screw properly
into place.

Your fixture is now assembled and
ready to use. Enjoy!

Bar

Figure 3

G

Figure 2

H

F

Ribbed side wire
from fixture

Smooth side wire
from fixture

Ground wire
from fixture

Bulb

E

2014 QuoizelInc.

Need assistance with partsorassembly?CallQuoizelcustomer service at 1-631-273-2700

Thank you for purchasingaQuoizelproduct.

or visit us on-lineatwww.quoizel.com

1of2

Figure 4

April2014

TFIK8802

2.4mm 13G a

GND

QUIOZEL

(2)60W B10

Candelabra Base

Bulbs (Not Supplied)

PART NUMBER

NO.

1

2

3

18802TFIK

8952KIT

G8186SH

2

Fixture can only be
mounted in the
direction indicated

7”

NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"

REPLACEMENT PART DESCRIPTION

BASE TFIK8802

MOUNTING HARDWARE

SHADE TIFFANY INGLENOOK 7H X 16D

15.5”
5”

1

3

REQ.

1

1

1

2of2