Quoizel TFIK348VA User Manual

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

CEILING CANOPY

FIXTURE CHAIN

CROSSBAR

SHAKE PROOF WASHER A

LOCK NUT A

SHAKE PROOF WASHER B

SMALL LOOP

NIPPLE

FIGURE2

OUTLET BOX

LOCK NUT B

KNOB

HOUSE SUPPLY and

GROUND WIRES

OUTLET BOX SCREWS

not supplied()

FIXTURE SUPPLY and GROUND WIRE

FIXTURE LOOP

QUICK LINK

FIGURE1

MAIN ASSEMBLY

BAR

SOCKET

LOCK BALL

ASSEMBLY / INSTALLATION INSTRUCTIONS

1. Before

Turn power to the installation point OFF at circuit breaker

3 Refer to FIGURE1) Locate MAIN ASSEMBLY inside of SHADE and match the holes on BARS with holes on the

beginning the installation carefully unpack and identify all parts referring to the illustration.

top edge of SHADE. Place the LOCK SCREWS through the holes on the BARS and SHADE from the bottom up. Hand LOCK BALLS onto the LOCK SCREWS and hand tighten until snug to secure MAIN ASSEMBLY and SHADE together.

FOR CANADIAN INSTALLATION-PLEASE REFER TO PAGE 2:

(Refer to FIGURE1)

Fasten the CROSSBAR to the OUTLET BOX with (2) OUTLET BOX SCREWS(not supplied). Proceed to thread LOCK NUT A and SHAKE PROOF WASHER A onto the top end of NIPPLE. Thread NIPPLE into the center of CROSSBAR. Locate the LOCK NUT B onto the bottom end of the NIPPLE. Tighten LOCK NUT A against CROSSBAR with pliers until snug.

5 Locate FIXTURE CHAIN and determine desired hanging height of fixture Adjust chain by removing links

. .

if needed Proceed to attach the QUICK LINKS on the end of FIXTURE CHAINS onto FIXTURE LOOPS and

SMALL LOOPS. Pass supply wire through one FIXTURE CHAIN alternating links and pass the supply wire through CEILING CANOPY

SMALL LOOP

MAKING THE WIRING CONNECTIONS:

(Quoizel recommends (2) people for the next 2 installations)

wire connectors (not supplied)connect the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE to

;

the FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE); connect the HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap each connection with approved electrical tape.

7. With the proper connections made, proceed to thread the LOCK NUT B and SHAKE PROOF WASHER B onto the bottom of the NIPPLE. Lift CEILING CANOPY upward and make the center hole over the end of NIPPLE Be sure that all wires are carefully tucked into OUTLET BOX cavity Secure by threading KNOB onto end of NIPPLE and hand tighten until snug

Using

IS TFIK348 Page1of3 2006 8-17--

SHADE

LOCK SCREW

8. Install bulbs referring to fixture markings and or labels for maximum wattage

9. Restore power to the installation point ON Retain this sheet for

future reference

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN!

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

COTTER PIN

HOUSE SUPPLY and GROUND WIRES

FIXTURE SUPPLY and GROUND WIRES

FIGURE1

/- ,

3 8 18NIPPLE WASHER HEX NUT with SHAKE PROOF WASHER included

HOLE DRILLED INSIDE OUTLET BOX

COUPLING

()

OUTLET BOX

SHAKE PROOF WASHER

HEX NUT

INSTALLATION INSTRUCTIONS ()FOR FIXTURES OVER 25 LBS Canada Only.--

Please use the information outlined in this sheet for the ceiling installation part of your fixture assembly.

Quoizel recommends a licensed electrician or contractor be consulted for this installation.

1 Before installing fixture carefully unpack and identify all parts referring to illustration FIGURE Be

., .

sure the power to the installation point is OFF

. .

The weight of this fixture will require a means of support independent of the OUTLET BOX This fixture must be supported by 3 8 18 NPSM NIPPLE supplied The NIPPLE should be positioned so that 3 4 protrudes into the OUTLET BOX cavity

/" . :

/- ( )

be attached to a structural or bridging member of sufficient strength to support the fixture weight

A COTTER PIN has been included and should be installed into the top of 3 8 18 NPSM NIPPLE above HEX NUT for added safety A clearance hole must be drilled on the inside top center of the OUTLET BOX Please refer to Figure 2 page 3 for detailed illustration We recommend the consultation of a

., .

licensed electrician or contractor due to the complexity of this installation

3 With the 3 8 18 NPSM NIPPLE properly situated locate COUPLING and proceed to thread onto the

./- ,

end of the NIPPLE protruding into the OUTLET BOX Thread COUPLING onto pipe until tight Tighten the top SET SCREW with pliers to secure COUPLING to NIPPLE Locate the NIPPLE and thread HEX NUT onto top end Pass SHAKE PROOF WASHER over top end Thread top end of NIPPLE into the COUPLING Using pliers snug HEX NUT up against the COUPLING Tighten lower SET SCREW with

., .

pliers to secure the NIPPLE Proceed to thread CROSSBAR and secure it onto OUTLET BOX by

2 OUTLET BOX SCREWS not supplied

() ( ).

4 Turn back to STEP 5 PAGE 1 for rest installations

Note the opposite end of the NIPPLE must

/- ,

CROSSBAR

NIPPLE

CEILING CANOPY

FINIAL

IS TFIK348 Page2of3 2006 8-17--

+ 1 hidden pages