Quoizel TFIK2817VA User Manual

ASSEMBLY / INSTALLATION INSTRUCTIONS

6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com

..

CROSSBAR

SHAKE PROOF
WASHER A

LOCK NUT A

LOCK NUT B

SHAKE PROOF
WASHER B

FIXTURE CHAIN

SOCKET
CLUSTER

STEEL RING

,.

NIPPLE

NIPPLE

FINIAL

FIGURE1

OUTLET BOX

HOUSE SUPPLY and

GROUND WIRES

OUTLET BOX SCREWS

not supplied()

GREEN GROUND SCREW

CANOPY CHAIN LOOP

FIXTURE SUPPLY
and GROUND WIRE

CEILING CANOPY

CANOPY LOCK RING

FIXTURE SUPPLY
and GROUND WIRE

FIXTURE LOOP

STEEL RING

DECORATION
CHAIN

HEX COUPLING

HEX NUT

KNURLED NUT

SHADE

1 Before beginning the installation carefully unpack and

.

identify all parts referring to the illustration FIGURE1

2 Turn power to the installation point OFF at circuit breaker

..

3 Thread top end of NIPPLE into HEX COUPLING underside

.

of SOCKET CLUSTER Use plier thread HEX NUT

,().

.,

against HEX COUPLING and hand tighten until snug

,

.

Proceed to adjust KNURLED NUT to proper location for
SHADE and FINIAL

4 Quoizel recommends 2 people for this step Lift SHADE

.( )

.

upward and make the hole on the bottom of it over end of

NIPPLE Attached one end of DECORATION CHAIN onto
STEEL RING on the top side of fixture Proceed to attach
another end of CHAIN onto STEEL RING inside of SHADE

.

.

.
Thread FINIAL onto end of NIPPLE and hand tighten until
snug

.

Fasten the CROSSBAR to the OUTLET BOX with

5

.

(2)OUTLET BOX SCREWS (not supplied). Proceed to
thread LOCK NUT A and SHAKE PROOF WASHER A onto
the top end of NIPPLE. Thread NIPPLE into the center of
CROSSBAR. Locate the LOCK NUT B onto the bottom end
of the NIPPLE. Tighten LOCK NUT A against CROSSBAR
with plier until snug.

. Locate the FIXTURE CHAIN and determine desired

6

hanging height of fixture. Adjust chain by removing links if
needed. Please note that depending on chain material
thickness, you might be required to use chain pliers to
spread links open. Proceed to attach one end of chain to
FIXTURE LOOP, attached to top of fixture. Pass the fixture
wires through FIXTURE CHAIN alternating links. Proceed
to pass the fixture wires through the following mounting
components in this order: 1) CANOPY LOCK RING;

2) CEILING CANOPY 3 CANOPY CHAIN LOOP 4 SHAKE
PROOF WASHER B and LOCK NUT B 5 NIPPLE
6 LOCK NUT A and SHAKE PROOF WASHER A

).

. (2 people recommended for the

Making the connections:

7

;) ;)

;) ;

remaining steps) Position the fixture under the ceiling
mounted outlet box. Pass SHAKE PROOF WASHER B over
the NIPPLE. Thread CANOPY CHAIN LOOP onto NIPPLE.
Thread LOCK NUT B down the NIPPLE, against the
CANOPY CHAIN LOOP and snug with pliers. Pass the
wires through the NIPPLE. Take up wire slack and trim
wires so that approx. 6” will remain inside outlet box.
Proceed to attach the top of the FIXTURE CHAIN to the
bottom of the CANOPY CHAIN LOOP. Using wire
connectors(not supplied) connect the HOUSE GROUND

WIRE to the FIXTURE GROUND WIRE connect the HOUSE

;

WHITE WIRE to the FIXTURE SUPPLY WIRE (WHITE or
RIBBED SIDE); connect the HOUSE BLACK (or RED) WIRE
to the FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.

8

. With the proper connections made, proceed to push the

CEILING CANOPY upward over the OUTLET BOX. Be sure
that all wires are carefully tucked into the OUTLET BOX
cavity. Secure canopy against ceiling by threading CANOPY
LOCK RING onto the CANOPY LOOP. Tighten until snug.

9

./

Install bulbs referring to fixture markings and or labels for

maximum wattage

10

. Restore power to the installation point ON. Retain this

.

sheet for future reference.

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!

IS TFIK2817
2006 5---9