Quoizel TFIK1817VA User Manual
Assembly Instruction Sheet #IS-TFIK1817VA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wirestrippers,electrical tape, safety glasses.
BulbRecommended: (3) MediumBase100W Maximum,Alternatebulb (3) 23W CFL
EstimatedAssembly Time:
Preparation:
present.Ifany parts are missingordamaged, do not attempttoassemble, install, or operatethefixture. Contact customer serviceforreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering July result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
,.
20-30minutes
Identifyandinspect all parts beforebeginninginstallation. Check package contentlistand diagrams below tobesure all parts are
For Style TFIK1817VA
Package Contents
Fixture Loop
A
x1
Shade
B
x1
Hardware Contents
Crossbar
AA
x1
Lock Washer
BB
x2
Hex Nut
CC
x2
Long Nipple
DD
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the
Outlet Box with the head of the
Green Ground Screw facing you.
Secure it with Outlet Box Screws
(not included) Tighten until snug..
EE
GG
Green
Ground
Screw
Knurled Nut
C
x1
Socket
D
Assembly
x1
Canopy
Chain Loop
x1
Canopy Lock
FF
Ring
x1
Fixture Chain
x1
Ceiling
HH
Canopy
x1
Outlet Box
AA
Outlet Box
Screw (not
included)
Figure 1
STEP 2 Install Canopy
Chain Loop and Nipple
A. Thread one Hex Nut (CC) to
B. Thread another Hex Nut (CC)
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (HH).
STEP 3 Install Shade and SocketAssembly-
A. Place Socket Assembly (D) inside of Shade (B). Pass the nipple on
-
* Pliers is required for this
step.
one end of the Nipple (DD)
until it is at least 0.25” from
the end. Pass one Lock
Washer (BB) over the end of
the Nipple (DD) and thread
the Canopy Chain Loop (EE)
onto the Nipple (DD). By
using pliers, thread the Hex
Nut (CC) against the Canopy
Chain Loop (EE) and hand
tighten until snug.
to the middle of the Nipple
(DD). Place another Lock
Washer (BB) over the Nipple
(DD) and then thread the
Nipple (DD) into the
Crossbar (AA) until the
Nipple (DD) is about 0.375”
above the Crossbar (AA).
(EE). Place the Ceiling Canopy (HH) over the Canopy Chain Loop
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (HH)
to rest against the ceiling when held in place by the Canopy Lock
Ring (FF).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
the top end of SocketAssembly (B) through the hole on Shade (B)
AA
Figure 2
DD
BB
CC
EE
FF
CC
BB
Step B
Step A
HH
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
August2014
and secure with Knurled Nut (C).
Tighten until snug.
B. Thread the Fixture Loop (A) onto
the Nipple at the top end of the
Socket Assembly (D) and hand
tighten until snug.
A
C
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
B
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
D
Figure 3
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
the links if needed.
*
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
Chain (GG) alternating links. After the wires are through the Fixture
Chain (GG), pull the Supply Wires and the Ground Wire through the
Canopy Lock Ring (FF) and the Ceiling Canopy (HH) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop. Lift the
fixture and Fixture Chain (GG) up and Attach the other end of the
Fixture Chain (GG) onto the Canopy Chain Loop (EE). The fixture
will now hang safely. Close the chain loop at the Ceiling Canopy
Loop (EE).
D. Feed the Supply Wires and Ground Wire through the Canopy Chain
Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 5 for wire connections.
F. Raise the Ceiling Canopy (HH) and Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until
tight.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Figure 5
STEP 6 - Install Bulb
A.10This fixture uses standard bulb with
medium base . Maximum 0 watts.
Insert bulb and screw snugly into place.
Your fixture is now assembled and ready
to use. Enjoy!
TFIK1817VA
FINISH: VALIANT BRONZE
NOTE: ONE LIGHT SHOWN FOR
ILLUSTRATION PURPOSES ONLY.
8” Dia.
3
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 6
3”
Socket
Bulb
Suggested chain length for Ceiling height :
8’ ceiling : use 16 links of chain
9’ ceiling : use 26 links of chain
10’ ceiling : use 36 links of chain
Supply Wires
and Ground Wire
GG
Figure 4
DD
EE
FF
A
HH
(3)100W Medium
Bulbs
Base
(Not Supplied)
2
1
4
17” SQ.
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
NO.
PART NUMBER
11817VATFIK
1
M1195CHVA
2
J860KIT
3
G2213SH
4
REPLACEMENT PART
BASE
CHAIN
MOUNTING HARDWARE
SHADE
64.5” OVERALL
HEIGHT
INCLUDES
48” CHAIN()
12.5”
9”
REQ.
1
1
1
1
2014 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
August2014
Loading...