Quoizel TFEC5103VB User Manual

Assembly Instruction Sheet #IS-TFEC5103VB

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

Quoizel, Inc. 6 Corporate Parkway Goose Creek, SC 29445

Customer Service Phone 631.273.2700 Fax 631.231.7102 www.quoizel.com

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject glass parts to any shock while in operation or shattering may result.

Care of Tiffany Style Shade

A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.

For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.

For Style TFEC5103VB

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,

safetyglasses.

BulbRecommended: (3) MediumBase 100W Maximum,Alternatebulb (3) 23W CFL EstimatedAssembly Time:30-45minutes

Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams

belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or operatethe fixture. Contact customer serviceforreplacement parts.

If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or mineral oil applied directly to oxidized areas and the soldered area will return to like new.

Package Contents

Column

Side Arm

STEP 1 Install Column, SideArm and

A. Thread Column (A) onto the Nipple on

Socket Assembly together

the top of SocketAssembly (C), hand

Socket Assembly

Lock Ball

Shade

Socket Collar

Figure 1

Hardware Contents

2.4 m m 13 Ga

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws (not included) Tighten until snug..

GND

Lock Washer

QUIOZEL

Hex Nut x2

Nipple x1

Crossbar x1

Canopy Chain Loop

Canopy Lock Ring

Fixture Chain

Quick Link

Ceiling Canopy

tighten until sung.

B. Pass the hole on one side of Side Arm

(B) through the Bolt on the Column (A), secure with Lock Ball (D). Hand tighten until sung. Pass the hole on the other side of Side Arm (B) through the Bolt on the Socket Assembly (C), secure with Lock Ball (D). Hand tighten until sung.

Bolt

Nipple

Outlet Box

Outlet Box Screw (not included)

Green Ground Screw

Figure 2

2014 Quoizel Inc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

1of3

April2014

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the Nipple (DD). By using pliers, thread the Hex Nut (CC) against the Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop (EE) against the ceiling to determine the correct position of the Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to rest against the ceiling when held in place by the Canopy Lock Ring (FF).

D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).

Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in place.

Step B

Supply Wires

and Ground Wire

Figure 4

Step A

Figure 3

STEP 4 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

the links if needed.

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop (A)

and the Canopy Chain Loop (EE), pull the supply wires through the Fixture Chain (GG) alternating links.After the wires are through the Fixture Chain (GG), pull the Supply Wires and the Ground Wire through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A)

with one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up And Attach the other end of the Fixture Chain (GG) onto the Canopy Chain Loop (EE) with another Quick Link (HH). The fixture will nowhang safely. Close the chain loop at the Ceiling Canopy Loop (EE).

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires

leaving approximately 8” of wire extending from the Outlet Box. E. Refer to Step 6 for wire connections. F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the

Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten

the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until

tight.

Suggested chain length for Ceiling height :

8’ ceiling : use 8 link of chain and 2 quick links

9’ ceiling : use 18 links of chain and 2 quick links

10’ ceiling : use 28 links of chain and 2 quick links

STEP 5 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and prepare wire ends according to instructions supplied with connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side

Wire from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture. E. Twist connectors until wires are tightly joined together. F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

White wire

from supply

Black wire from supply (or Red)

Ground wire

from supply

Ribbed side wire from fixture

Smooth side wire from fixture

Ground wire from fixture

Figure 5

2014 Quoizel Inc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

2of3

April2014

+ 1 hidden pages