Quoizel TFCS1510VB User Manual
Assembly Instruction Sheet #IS-TFCS1510VB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches
during shipment. If the oil applied is too heavy you can remove the excess oil film with a paper towel. Gently
wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and
wipe gently.
,.
For Style TFCS1510VB
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (3) MediumBase 100W Maximum,Alternatebulb (3) 23W CFL
EstimatedAssembly Time:30-45minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a
small amount of lemon oil or mineral oil applied directly to oxidized areas and the soldered area will return to
like new.
Package Contents
Shade
B
x3
Socket Collar
C
x3
Fixture Body
A
x1
STEP 1 adjust the wire length-
A. Adjust h what you wantthe Wire Clasp (G) at a proper lengt . By
using screw driver thread the Screw. Hand tighten until snug.
Wire Clasp
Screw
A
Figure 1
Crossbar
AA
x1
Lock Washer
BB
x1
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Green Ground
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to White Wire from
fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Black
Wire from fixture.
Screw
Hardware Contents
Hex Nut
CC
x1
Nipple
DD
x1
Finial
EE
x1
Outlet Box
AA
Outlet Box Screw
(not included)
2013 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
December2013
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 5 - Install Shade to fixture
A. Place Shades (B) over the Sockets on the Fixture Body (A), secure
with Socket Collars (C), hand tighten until sung.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
White wire
from fixture
Black wire
from fixture
Ground wire
from fixture
Figure 3
STEP 4 Install Fixture Body-
* Pliers is required for this step.
A. Thread Hex Nut (CC) to the Nipple (DD) place Lock Washer (BB)
,
over the Nipple (DD) and then thread the Nipple (DD) into the
Crossbar (AA) until the Nipple (DD) is about 0.375” above the
Crossbar (AA).
B. Place the Ceiling Canopy (HH) over the Nipple (DD) against the
ceiling to determine the correct position of the Nipple (DD). Thread
the Finial (E) onto the Nipple (DD). Tighten until sung.
BB
CC
AA
DD
Ceiling Canopy
EE
Figure 4
A
Socket
B
Figure 5
C
STEP 6 - Install Bulb
A. This fixture uses standard bulbs with medium screw bases.
Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Your fixture is now assembled and ready to use.
Enjoy!
Socket
TFCS1510VB
FINISH: VINTAGE BRONZE
2.4mm
13Ga
QUOIZEL
R
GND
Base
Medium
Bulbs
(3) 100W
(Not Supplied)
PART NUMBER
NO.
G3783SH
1
10”
10”
8”
5”Dia.
1
12”
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
SHADE TIFFANY 5"D 3
Bulb
Figure 6
2013 Quoizel Inc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
December2013
Loading...