Quoizel TFAV2823VB User Manual

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

ASSEMBLY / INSTALLATION INSTRUCTIONS

1 Before beginning the installation carefully unpack and

identify all parts referring to the illustration.

CROSSBAR

LOCK WASHER A

LOCK NUT A

LOCK NUT B

LOCK WASHER B

FIXTURE CHAIN

FIXTURE CANOPY

OUTLET BOX

HOUSE SUPPLY and GROUND WIRES

OUTLET BOX SCREWS

not supplied()

NIPPLE

CANOPY CHAIN LOOP

FIXTURE SUPPLY and GROUND WIRE

CEILING CANOPY

CANOPY LOCK RING

FIXTURE SUPPLY and GROUND WIRE

FIXTURE LOOP

DECORATIVE ARM

2 Turn power to the installation point OFF at circuit

breaker

3 Unfold DECORATIVE PARTS to proper location Lift

RING upward and match the end of DECORATIVE PART into the hole on the KNOB Secure them together

by threading LOCK SCREW into mounting holes on KNOB Hand tighten until snug

4 Locate NIPPLE with HEX NUTS Thread one end of

NIPPLE into HEX COUPLING underside of SOCKET CLUSTER Using plier thread HEX NUT against HEX COUPLING and hand tighten until snug Adjust another

HEX NUT on the end of NIPPLE to proper location for rest components Place CAP over the end of NIPPLE and secure with KNURLED NUT Hand tighten until snug

5 Lift SHADE upward and make the hole on the bottom of

it over the end of NIPPLE Thread FINIAL onto end of NIPPLE and hand tighten until snug to secure it

6 Fasten the CROSSBAR to the OUTLET BOX with 2)

(

OUTLET BOX SCREWS (not supplied). Proceed to thread LOCK NUT A and LOCK WASHER A onto the top end of NIPPLE. Thread NIPPLE into the center of CROSSBAR. Locate the LOCK NUT B onto the bottom end of the NIPPLE. Tighten LOCK NUT A against CROSSBAR with plier until snug.

7. Locate the FIXTURE CHAIN and determine desired hanging height of fixture. Adjust chain by removing links if needed. Please note that depending on chain material thickness, you might be required to use chain pliers to spread links open. Proceed to attach one end of chain to FIXTURE LOOP, attached to top of fixture. Pass the fixture wires through FIXTURE CHAIN alternating links. Proceed to pass the fixture wires through the following mounting components in this order : 1) CANOPY LOCK RING; 2) CEILING CANOPY 3 CANOPY CHAIN LOOP 4 LOCK WASHER B and LOCK NUT B 5 NIPPLE 6

););)

LOCK NUT A and LOCK WASHER A

;) ;

LOCK

SCREW

SHADE

SOCKET

CLUSTER

FINIAL

HEX COUPLING

NIPPLE with HEX NUTS

KNURLED NUT

KNOB

CAP

MAKING THE CONNECTIONS:

(2 people recommended for the remaining steps)

Position the fixture under the ceiling mounted outlet box. Pass LOCK WASHER B over the NIPPLE. Thread CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK NUT B down the NIPPLE, against the CANOPY CHAIN LOOP and snug with pliers. Pass the wires through the NIPPLE. Take up wire slack and trim wires so that approx. 6” will remain inside outlet box. Proceed to attach the top of the FIXTURE CHAIN to the bottom of the CANOPY CHAIN LOOP. Using wire connectors (not supplied) connect the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE to the

RING

;

FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE); connect the HOUSE BLACK (or RED) WIRE to the FIXTURE SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap each connection with approved electrical tape.

9. With the proper connections made, proceed to push the CEILING CANOPY upward over the OUTLET BOX. Be sure that all wires are carefully tucked into the OUTLET BOX cavity. Secure canopy against ceiling by threading CANOPY LOCK RING onto the CANOPY LOOP. Tighten until snug.

10 Install bulbs referring to fixture markings and or labels

for maximum wattage

11. Restore power to the installation point ON. Retain this sheet for future reference.

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN!

IS TFAV2823

Revised 2008 04 17