
6 CORPO RATE PAR KWAY
GOOSE C REE K, SC. 29 445
www.quoize l. com
INSTRUCTION SHEET IS-TF879C
STYLE NUMBER: TF879CVB
PAC KAGE CONT ENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
N
Crossbar
Green G round S crew
Hex Nut
Nipple
Lock Washe r
Canopy Chain Loop
Canopy Lock Ring
Fixtu re Chai n
Ceiling Canopy
Nipple with Nuts
Finial
Socke t Assemb ly
Side Chain
Shade
Descriptio n
Quant ity
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
1pc
3pcs
1pc
ISSUE D 03-20 10
A
B
C
D
E
F
G
H
I
J
L
M
!
WARNIN GS AND CAU TIONS
WAR NI NG :
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CA UT IO NS :
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PR EPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tools Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers,
Electrical tape, Wire cutters, Safety glasses & (3) 100W A19 medium base bulbs.
● Helpful Tools (not included): Wire strippers.
N
K
1 OF 3

IN STALLATION IN STRUC TIONS
ST EP 1:
a. Secure the Crossbar onto the Outlet Box with Outlet Box
Screws. Tighten until snug.
ST EP 2:
* Pliers is required on this step.
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar.
c. Using pliers, thread the Hex Nut against the crossbar
and hand tighten until snug.
d. Thread another Hex Nut onto the bottom end of the
Nipple.
Crossbar
STYLE N UMBER : TF879 CVB
Outle t Box
Crossbar
Outle t Box
Screw
Lock Washe r
Hex Nut
Nipple
ST EP 3:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed.
* Please note that depends on chain material thickness,
you might be required to use chain pliers to spread links
open.
b. Pull the supply wires through the Fixture Chain alternating
links. And then pull the wires through the following
components in turn:
Canopy Lock Ring, Ceiling Canopy, Canopy Chain Loop,
Lock Washer, and Nipple.
c. Place Lock Washer over the end of the Nipple and thread
the Canopy Chain Loop onto the end of the Nipple.
d. Using plier, thread the Hex Nut against the Canopy Chain
Loop and tighten until snug.
e. Attach one end of the Fixture Chain onto the Fixture Loop
and attach the another end of the chain onto the Canopy
Chain Loop.
f. Refer to Step 4 - Wire Connections to connect wires.
g. Push the Ceiling Canopy upward over the Outlet Box.
h. Thread the Canopy Lock Ring onto the Canopy Chain Loop
and tighten until snug to secure the Ceiling Canopy.
Hex Nut
Nipple
Hex Nut
Lock Washe r
Canopy Chain Loop
Ceiling
Canopy
Fixtu re Chai n
2 OF 3
Canopy Lock Ring
Fixtu re Loop

IN STALLATION IN STRUC TIONS
ST EP 4:
*Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White ( or Ribbed) Wire to the
Fixture Supply Wire (White or Ribbed Side).
c. Connect the House Black(or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet
Box.
ST EP 5:
a. Screw the Hex Nut end of the Nipple with Nuts into the Hex
Coupling underside of the Socket Assembly. Using pliers,
thread the Hex Nut against the hex coupling underside of
the Socket Assembly. Hand-tighten until snug.
STYLE N UMBER : TF879 CVB
WHITE O R RIBBE D
FROM HO USE
BLACK(OR RE D) WIRE
FROM HO USE
GROUN D WIRE GROUN D WIRE
FROM HO USE FROM FI XTURE
WHITE O R RIBBE D
FROM FI XTURE
BLACK O R SMOOT H
FROM FI XTURE
Socke t Assemb ly
ST EP 6:
a. Place the Shade over the end of the Nipple. Attach one
end of the Side Chain onto the Hook on the side of the
Fixture Canopy. Attach the another end of the Side Chain
onto the Hanger inside of the Shade.
b. Adjust the Knurled Nut on the Nipple against the inside
bottom of the Shade. Then thread the Finial onto the Nipple
and hand-tighten until snug.
Knurl ed Nut
Nipple with Nuts
Fixtu re Cano py
Hook
Side Chain
Nipple
Shade
Finial
ST EP 7:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
3 OF 3
Hanger