Quoizel TF878F User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver, pliers,wirecutters, wire strippers,electricaltape, safety glasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:
present.Ifany parts aremissingor damaged, donotattempt to assemble,install,or operate thefixture.Contact customer serviceforreplacement
parts.
,.
(2)MediumBase 100W Maximum,Alternate bulb (2)23WCFL
20-30minutes
Identifyandinspect all partsbeforebeginning installation. Checkpackagecontent list anddiagramsbelow to besureall parts are
Assembly Instruction Sheet #IS-TF878F
For Style TF878F
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 1 Install Nipple with HEX
A. Thread the Socket Assembly ,
B. Pull the cord from the Base as
C. Thread have hex nut end of
D. Place Spacer and Check Ring
E. Thread Big Knurled Nut onto
F. Place the Flat Washer and the
G. This fixture uses standard bulb
-
Nut, Shade and Bulb
the , the and
Threaded Rods Rod
the Base together as shown.
Hand tighten until snug.
you assemble the parts together
to remove the excess cord
between parts.
Nipple with Hex Nut into Hex
Coupling on the top of Socket
Assembly .
over the Nipple. Secure by
thread Small Knurled Nut onto
the Nipple, hand tighten until
snug.
Nipple. Hand tighten until snug.
Shade over the Nipple. Adjust
the Big Knurled Nut to proper
location for the Flat Washer, the
Shade and Finial. secure by
thread Finial onto the Nipple,
hand tighten until snug.
with medium base . Maximum
100 watts. Insert bulb and screw
snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Need assistance with partsorassembly?CallQuoizel customer service at 1-631-273-2700
2014 Quoizel Inc.
Flat
Washer
x1
Small Knurled
1x Nut
Nipple with
Hex Nut x 1
Bulb (not
included)
Rod
x1
Threaded
Rod
x2
Figure 1
Finial
X1
Shade
X1
Big Knurled
Nut x 1
Check Ring
Spacer
x1
Socket
Assembly
x1
Base
x1
Thank you for purchasingaQuoizelproduct.
or visit us on-lineatwww.quoizel.com
FINISH: VINTAGE BRONZE
(2) 100W
NO.
1
2
3
4
1of1
TF878F
Medium
Base
Bulbs
(Not Supplied)
PART NUMBER
1878FTF
M2364FIVB
M2402KIT
G2524SH
8.5”
4
62”
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BASE FOR TF878F
FINIAL VINTAGE BRONZE 0.75"D X 1.40"H
KIT SHADE VINTAGE BRONZE FOR TF878F
SHADE 18"D FOR TF878FTIFFANY
18”Dia.
2
3
1
10”Dia.
April2014
REQ.
1
1
1
1
Loading...