Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TF7110Z
For Style TF7110Z
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired:None
BulbRecommended: (1) T3 Bi Pin Bulb 50W Maximum (Supplied)
EstimatedAssemblyTime:15-20 minutes
Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackage
contentlistanddiagramsbelowtobesureallpartsarepresent.Ifanypartsaremissing
ordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer
serviceforreplacementparts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering Octoberresult.
Do not touch the bulb with bare hands use a cloth or glove.
Package Contents
Part
A
B
C
D
E
2013QuoizelInc.
Description
Fixture Body
Shade
Lock Ball
Diffuser
T3 Bulb
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
Quantity
1pc.
1pc.
2 pcs.
1pc.
1pc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
A
B
1of3
C
D
E
May2014
Page 2
TF7110Z
FINISH: MEDICI BRONZE
18.5”
6” Sq.
2
2.5”
3
4
6” Dia.
17”
1
5
(1)50W T3 BI
PIN BULB
(Supplied)
PART NUMBER
NO.
1
2
3
4
5 K729SWK
97110ZTF
I816SC
G6220SH1
G262LEX
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BASE HALOGEN TABLE TASK LAMP
BULB 50W 120V GY6.35 CLEARHALOGEN
GLASS TIFFANY TASK W/TABS
LENS GLASS 4-7/8X1/8 SAFETY 1
SWITCH REPLACEMENT TF7110 1
2of3
REQ.
1
1
1
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-TF7110Z
For Style TF7110Z
STEP 1 - Install Shade
A. Attach the Shade (B) to the Socket Assembly. Pass the
Bolts on the Socket Assembly through the Small Holes
on the bottom of the Shade (B). Secure by threading the
Lock Balls (C) onto the Bolts. Hand tighten until snug.
STEP 2 - Install Bulb
A. This fixture uses T3 Bi Pin bulb. Maximum 50 watts.
B. Insert bulb and push snugly into place.
IMPORTANT:
a cloth or glove.
Do not touch the bulb with bare hands use
Figure 1
Socket Assembly
Bolt
Small Hole
Shade
Lock Ball
Figure 2
Socket
Bulb
STEP 3 Install Diffuser to Shade-
A.
Pass the Gaps on the Diffuser (D) over the Tabs on the
Shade (B) and then rotate the Diffuser (D). Do not free
your hands until the diffuser is seated onto the tabs.
Your fixture is now assembled and ready to use.
Enjoy!
Tab
Gap
Figure 3
Shade
Diffuser
CAUTION FOR BULB REPLACING
A. When replace bulb, turn off power and allow lamp to cool. For safety purpose, wear gloves and eye protection.
B. If bulb is scratched or cracked, DO NOT use the lamp to avoid breakage during use or installation.
C. Use only in fixtures rated for lamps wattage and voltage.
D. Lamp operate under high pressure generating intense heat. Prevent contact with liquid and combustible
materials.
Need assistance with partsor assembly? Call Quoizelcustomer service at 1-631-273-2700
2013 Quoizel Inc.
Thank you for purchasinga Quoizel product.
or visit us on-lineat www.quoizel.com
3of3
May2014
Loading...