Quoizel TF6669VB User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
ToolsRequired: Flatheadscrewdriver,Phillipsscrewdriver, pliers,wirecutters, wire strippers,electricaltape, safety glasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:
present.Ifany parts aremissingor damaged, donotattempt to assemble,install,or operate thefixture.Contact customer serviceforreplacement
parts.
,.
(2)MediumBase 60W Maximum,Alternate bulb (2)13WCFL
20-30minutes
Identifyandinspect all partsbeforebeginning installation. Checkpackagecontent list anddiagramsbelow to besureall parts are
Assembly Instruction Sheet #IS-TF6669VB
For Style TF6669VB
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 1 Install Nipple with
A. Thread have hex nut end of
B. Place Spacer and Check
C. Thread Big Knurled Nut onto
D. Place the Flat Washer and
E. This fixture uses standard
-
HEX Nut, Shade and
Bulb
Nipple with Hex Nut into Hex
Coupling on the top of the
base .
Ring over the Nipple. Secure
by thread Small Knurled Nut
onto the Nipple, hand tighten
until snug.
Nipple. Hand tighten until
snug.
Shade over the Nipple.
Adjust the Big Knurled Nut to
proper location for the
Shade and Finial. secure by
thread Finial onto the
Nipple, hand tighten until
snug.
bulb with medium base .
Maximum 60 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
Figure 1
Flat Washer
1x
Small Knurled
1x Nut
Bulb (not
included)
Finial
X1
Shade
X1
Big Knurled
Nut x 1
Check Ring
Spacer
x1
Nipple with
Hex Nut x 1
Base
x1
TF6669VB
(2) 60W
Base
(Not Supplied)
PART NUMBER
NO.
M860BLA
1
2
16669VBT
C714FIR
3
4
G6907SH
Medium
Bulbs
16”Dia.
3
4
8”
23”
1
2
?
7.5” Dia
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
BALL 5/8" DIABRASS
BASE VINTAGE BRONZE TABLE LAMP
FINIAL 1/8F
GLASS TIF 8H X 16D
REQ.
1
1
1
1
2014 Quoizel Inc.
Need assistance with partsorassembly?CallQuoizel customer service at 1-631-273-2700
Thank you for purchasingaQuoizelproduct.
or visit us on-lineatwww.quoizel.com
1of1
June2014
Loading...