6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS TF489P01: STYLE NUMBER TF489P01VB:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
Crossbar
Green Ground Screw
Mounting Screws
Lock Washer
Hex Nut
Mounting Ball
6” Rod
12” Rod
Ceiling Canopy
ShadeAssembly
Description
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
2pcs
2pcs
1pc
1pc
ISSUED 08-2009
I
A
B
C
J
D
E
F
G
H
!
WARNINGS AND CAUTIONS
WARNING:
Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
●
switching off the circuit breaker or removing the fuse.
CAUTION:
These instructions are provided for your safety. It is very important that they are read completely before
●
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
●
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
EstimatedAssembly Time : 20 30 minutes
●
Tools Required forAssembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
●
Electrical Tape, Wire Cutters, Safety Glasses &1, 100 Watt, Type - A Medium Base Bulbs.
Helpful Tools (not included) : Wire Strippers.
●
,
1 OF 3
INSTALLATION INSTRUCTIONS
STEP 1:
a. Determine the Rods to be assembled according to your
desired hanging height.
b. Pass the Supply Wires with Ground Wire through the
chosen Rods and then thread Rods and Shade Assembly
together as shown. Tighten until snug.
STYLE NUMBER TF489P01VB:
6” Rod
6” Rod
12” Rod
12” Rod
Supply Wires with
Ground Wire
ShadeAssembly
STEP 2:
.
a Pass the Supply Wires with Ground Wire through the
Swivel and Ceiling Canopy.
.
b Thread the Swivel onto the top end of the Upper Rod and
hand tighten until snug.
STEP 3:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
.
Ceiling Canopy
Swivel
Supply Wire with
Ground Wire
Upper Rod
Mounting Screw
Crossbar
Hex Nut
Lock Washer
Outlet Box
Outlet Box Screw
2 OF 3
INSTALLATION INSTRUCTIONS
STEP 4:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ).
( )
carefully stuff all of the connected wires into the Outlet
.
Box
STEP 5 :
a Place the Ceiling Canopy onto Outlet Box aligning 2
.
holes in the Ceiling Canopy with 2 Mounting screws
threaded on the Crossbar and secure it against wall
with Mounting Balls
.
STYLE NUMBER TF489P01VB:
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
Mounting
Screw
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Mounting Ball
Outlet Box
Ceiling
Canopy
STEP 6 :
a Install the correct bulb referring to fixture markings and or labels for maximum wattage. / .
. . .Your installation is completed now Restore electricity Retain this sheet for future reference
3 OF 3
Loading...