Quoizel TF2819VB User Manual

ASSEMBLY INSTALLATION INSTRUCTIONS/

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

()2 OUTLET BOX

SCREWS

CANOPY CHAIN LOOP

CEILING CANOPY

FIXTURE CHAIN

FIXTURE SUPPLY WIRE and GROUND WIRE

CROSSBAR

NIPPLE

CANOPY LOCK RING

FIGURE1

GREEN GROUND SCREW

LOCK NUT A with SHAKE PROOF WASHER A

LOCK NUT B with SHAKE PROOF WASHER B

FIXTURE LOOP

HOOK

1 Before beginning the installation carefully unpack and

identify all parts referring to the illustration FIGURE1

2 Locate the CENTER ASSEMBLY and unravel FIXTURE

SUPPLY WIRE AND GROUND WIRE

3 Locate the CROSSBAR and with power to installation

point OFF secure to OUTLET BOX with 2 OUTLET

,()

BOX SCREWS not supplied Locate LOCK NUT A and SHAKE PROOF WASHER A Thread LOCK NUT

,().

().

A and SHAKE PROOF WASHER A onto top end of NIPPLE Thread the NIPPLE into the center of the CROSSBAR Locate LOCK NUT B and thread bottom end of NIPPLE Tighten LOCK NUT A against CROSSBAR with plier until snug

4 Locate the FIXTURE CHAIN and determine desired

hanging height of fixture Adjust chain by removing links if needed Please note that depending on chain material thickness you might be required to use chain pliers to spread links open Proceed to attach one end of chain to FIXTURE LOOP attach to the top of the fixture Ureavel FIXTURE SUPPLY and GROUND

WIRE and pass through FIXTURE CHAIN alternating links Proceed to pass the fixture wires through the

following mounting components in this order 1 CANOPY LOCK RING 2 CEILING CANOPY

););

3 CANOPY CHAIN LOOP 4 SHAKE PROOF WASHER

);)

B and LOCK NUT B 5 NIPPLE 6 LOCK NUT A and SHAKE PROOF WASHER A

;) ; )

FIXTURE CANOPY

CENTER ASSEMBLY

SHADE

STEM

4 SUPPORT RODS

() ,

or CHAINS Depends on style purchased

SOCKET CLUSTER

(

)

HOOK

Make the wire connections (Quoizel recommends

2 people for next 3 steps:)

Position the fixture underneath the CEILING MOUNTED OUTLET BOX and pass SUPPLY WIRE and GROUND WIRE through the center of NIPPLE Use wire connectors not supplied Connect the HOUSE GROUND WIRE to the FIXTURE GROUND WIRE connect the HOUSE WHITE or RIBBED SDIE WIRE to the FIXTURE WHITE or RIBBED SIDE WIER connect the HOUSE BLACK or RED WIRE to the FIXTURE BLACK

or SMOOTH SIDE WIER Make sure there are no

().

()

;

()

();

()

exposed wires and wrap each connection with approved electrical tape

6 Carefully tuck in all wiring into the OUTLET BOX and

thread the CANOPY CHAIN LOOP onto the bottom of NIPPLE Thread LOCK NUT B and SHADE PROOF WASHER B onto top of CANOPY CHAIN LOOP Tighten with pliers locate the CEILING CANOPY over the

CEILING MOUNTED OUTLET BOX and secure against ceiling by threading the CANOPY LOCK RING onto the CANOPY CHAIN LOOP Proceed to attach the top of FIXTURE CHAIN to the CANOPY CHAIN LOOP Carefully compress end of FIXTURE CHAIN to secure

7 Install bulbs referring to fixture markings and or labels

for maximum wattage

8 Locate STEM and thread into the bottom center of

SHADE LOOP

SOCKET CLUSTER Hand tighten until snug

9 Locate the SHADE and position the MOUNTING HOLE

at the bottom of the SHADE over the STEM Pass STEM through MOUNTING HOLE Proceed to attach

1 HOOK at end of SUPPORT ROD to 1 SHADE

() ()

FINIAL

LOOP inside of SHADE Repeat process for remaining arms Please note that depending on style purchased

.( ,

there might be SUPPORT ROD or CHAINS Locate

FINIAL and attach to end of STEM protruding from SHADE Tighten until snug

10 Attach tops of 4 SUPPORT RODS or CHAINS to

.() ()

the 4 HOOKS on the side of FIXTURE CANOPY

11 Restore the power to the installation point ON Retain

() .

this sheet for future reference

IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT A LICENSED ELECTRICIAN!

IS 646

Revised 2006 5 13