Quoizel TF1804SVB User Manual
Assembly Instruction Sheet #IS-TF1804SVB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
,.
For Style TF1804SVB
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended: (2) MediumBase 75W Maximum,Alternatebulb (2) 19W CFL
EstimatedAssembly Time:20-30minutes
Preparation:Identify and inspect all partsbeforebeginning installation. Check package contentlist and diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Package Contents
Hardware Contents
AA
Crossbar
x1
2.4 m m 13 Ga
GND
A
B
C
QUIOZEL
Ceiling
Canopy
x1
Shade
x1
Finial
x1
DD
Nipple
x1
STEP 1 Install Crossbar-
A. Attach the Crossbar (AA) to the
Outlet Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included)
Tighten until snug
.
STEP 2 Attach Nipple to Crossbar-
A. Locate the Nipple (DD) and thread
one Hex Nut (BB) onto it about half
way. Slip a Lock Washer (CC) onto it
and thread one end of the Nipple
(DD) into the center hole of the
Crossbar (AA).
B. Position the Ceiling Canopy (A) over
the outlet box, passing the mounting
hole in the center of the Ceiling
Canopy (A) over the end of Nipple
(DD).
C. Adjust the Nipple (DD) so approx 3/8
inch of the Nipple (DD) is protruding
from the mounting hole. This
adjustment may take a few tries.
D. When this length is achieved,
remove the Ceiling Canopy (A) and
tighten the Hex Nut (BB) up against
the underside of the Crossbar (AA)
with pliers.
STEP 3 - Wire Connections
.
Green Ground Screw
Outlet Box
Screw
AA
CC
BB
DD
Outlet
Box
AA
Figure 2
A
Hex Nut
BB
x1
Lock Washer
CC
x1
2014 Quoizel Inc.
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
EE
Flat
Washer
x1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
1of2
April2014
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 5 Install Bulb-
A. This fixture uses standard bulb with medium screw base. Maximum
75 watts.
B. Insert bulb and screw snugly into place.
Shade Holder
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
STEP 4 Attach Ceiling Canopy-
A. Position the Ceiling Canopy (A) and
Flat Washer (EE) to the ceiling by
passing the Nipple (DD) through the
center hole. Thread the Finial (C) to
the bottom end of the Nipple (DD).
Snug down assembly until the
Ceiling Canopy (A) is flush against
the ceiling.
* Be sure that there are no trapped
or pinched wires along the edge of
the Ceiling Canopy (A).
TF1804SVB
FINISH: VINTAGE BRONZE
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
Figure 4
Figure 3
AA
DD
EE
C
Socket
Bulb
STEP 6 Install Shade-
A. Locate the Shade (B) wedge in the two Shade Holders without
Spring. Pull the one Shade Holder with the Spring outside and
position the Shade (B) onto the bottom of the Ceiling Canopy (A).
The Shade Holder will engage the Shade (B) after release.
A
7” Dia.
A
B
Figure 5
Shade Holder
Figure 6
6”
4”
1
(2) 75W
NO.
1
Medium
Base
Bulbs
(Not Supplied)
PART NUMBER
G3826SH SHADE TIFFANY 16"D x 4”H 1
2014 Quoizel Inc.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of2
15.5” Dia.
16.5” Dia.
REQ.
April2014
Loading...