Quoizel TF1784VB User Manual

6 CORPORATE PARKWAY GOOSE CREEK SC 29445 www quoizel com

ILLUSTRATIONA

FIXTURE LOOP

CEILING INSTALLATIONINSTRUCTIONS FOR FIXTURES WEIGHING OVER 45 LBS.

NOTE: DUE TO THE HANGING WEIGHTOF THIS FIXTURE, QUOIZEL HIGHLY RECOMMENDSYOU CONSULT ALICENSED ELECTRICIAN OR QUALIFIED CONTRACTOR FOR THIS INSTALLATION. QUOIZEL RECOMMENDS (2)PEOPLE FOR THIS INSTALLATION

SMALLLOOP

PLATE

SOCKET

HEX COUPLING

1/8 IP. NIPPLE

DIFFUSER

JUNCTION BOX

NIPPLE with HEX NUT

HOOK

SIDE CHAIN

BULB(not supplied)

1. Before beginning fixture assembly, carefully unpack all ofthe parts referring to theillustration for parts identification.

2. Turn the power to installation point OFF at the circuit breaker.

3.Locate the Nipple with Hex Nut. Thread the top end ofthe Nipple into the HexCoupling underside of the Junction Box and leave the 1/8 IP. Nipple towards down.Use the plier, thread the HexNut against the Hex Coupling and hand tighten until snug.

4.(Refer to the ILLUSTRATION B) Positionthe Diffusersand make the holes on them over the Studs on the Plate. Place the Washers over the Studs and thread the Lock Ballsonto the Studs to scurethem. Hand tighten until snug.

Quoizel recommended two people for this step

Put one end of the Side Chain onto theSmall Loop on the sideof the Fixture Canopy. With another people, lift the Shadeupward and make the holeon the bottom center overthe 1/8 IP. Nipple. Place another end of the Side Chain onto the Hookson the top edge ofthe Shade.And then position the Shade Holder inside of the hole on the bottomof the Shade and locatethe Cap over the Shade Holder.Secure them with the Finial and tighten until snug.

STOPHERE! YOU MUST NOW REFER TO PAGE2 FOR SPECIFIC CEILING MOUNT INSTALLATION

INSTRUCTIONSAND PAGE 3 FORSAFETY CABLEINSTALLATION INSTRUCTIONS.

7. Install the correct bulbs referring to fixture markingsand/or labels for maximum wattage.

8. Restore power to the installation point ON. Retain this sheet for future reference.

ILLUSTRATION B

LOCK BALL

SHADE

CAP

SHADE HOLDER

FINIAL

DIFFUSER

WASHER

PLATE

IS TF1784

Revised 2006 12-19

Page1of3

IS-TF1784

Page2of3

Revised 2007-12-19

CANOPY

LOCK RING

QUICK LINK

CONNECTOR

FIXTURE SUPPLY

WIRES & SAFETY

CABLE

CANOPY

FIXTURE

CHAIN

QUICK-LINK

CONNECTOR

CANOPY CHAIN

LOOP

WIRE CONNECTORS

(NOT SUPPLIED)

LOCK WASHER B

LOCK NUT B

NIPPLE

LOCK WASHERA

SET SCREWS

LOCK NUTA

HEX COUPLING

HOUSE SUPPLY

and GROUND

WIRES

OPTION “B”

SAFETY CABLE

BRIDGING MEMBER

OUTLET BOX

(NOT SUPPLIED)

STRUCTURALOR

COTTER PIN

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

LOCK WASHER

FLATWASHER

3/8-18 NPSM PIPE

HEXNUT

OPTION “A”

SAFETY CABLE

NOTE: DUE TO THE HANGING WEIGHTOF THIS FIXTURE, QUOIZEL

HIGHLY RECOMMENDSYOU CONSULT ALICENSED ELECTRICIAN

OR QUALIFIED CONTRACTOR FOR THIS INSTALLATION.

QUOIZEL RECOMMENDS (2)PEOPLE FOR THIS INSTALLATION

7. Refer back to Page 1, Step 7 and finish installation. LOCK RING onto the CANOPY LOOP. Tighten until snug.

the CEILING CANOPY the the

against ceiling by threading CANOPY

6. Push the CEILING CANOPY up over the OUTLET BOX. Be sure that

all wires are carefully tucked into the OUTLET BOX cavity. Secure the

refer to Page 3 for the SAFETY CABLE / TUCK WASHER

INSTALLATION STEPS. Once that assembly is completed and the

cable is secured, you can refer back to Step #6 below to complete

your fixture installation.

STOP HERE! Before securing the CEILING CANOPY to the ceiling,

(black or smooth side). Wrap each connection with approved electrical

tape.

WIRE to the FIXTURE SUPPLY WIRE (white or ribbed side): connect

the HOUSE BLACK (or red) WIRE to the FIXTURE SUPPLY WIRE

Using wire connectors (not provided) connect the HOUSE GROUND

WIRE to the FIXTURE GROUND WIRE: connect the HOUSE WHITE

NOTE: DO NOT CUT THE SAFETY CABLE AT THIS TIME!

4. Next the HEX COUPLING and tighten with pliers or a wrench.

NOT THREAD NIPPLE BEYOND SIDE HOLE OPENING, DAMAGE TO

Tighten down HEX NUT B and LOCK WASHER B against it with pliers

or a wrench.

Raise the fixture and attach the FIXTURE CHAIN to the CANOPY

CHAIN LOOP with a QUICK-LINK CONNECTOR. Pull up all the slack

in the wire and the safety cable. You can now trim the wires down to

no less than 6” and begin splicing them together.

WIRING AND POSSIBLE ELECTRICAL SHOCK COULD OCCUR!

LOCK WASHER A up the NIPPLE until they are against the bottom of

until it is visible in the side hole opening. Thread LOCK NUT A and

Assemble the threaded NIPPLE into the bottom of the HEX COUPLING

the cable must exit the HEX COUPLING from the opposite side hole

of the wiring. Once that is determined and applied, return back to

the steps below.

choose either OPTION A or OPTION B. If you choose OPTION B,

STOP HERE! For SAFETY CABLE ROUTING, go to page 3 and

3. Position the fixture under the OUTLET BOX and pass the fixture wires

through the bottom center of the COUPLING.

Pull wires through the wire way hole on one side of the COUPLING.

LOCK WASHERS A and B.

NUTS A and B approx. ½” onto each end of the NIPPLE, also slip on

CHAIN LOOP; 4) LOCK WASHER B and LOCKNUT B;

5) NIPPLE; 6) LOCK NUT A and LOCK WASHER A Thread LOCK

CABLE through alternating links on the chain. Proceed to pass the

wires through the following mounting components in this order and how

it is shown in the illustration on the left:

1) CANOPY LOCK RING; 2) CEILING CANOPY; 3) CANOPY

Next decide the length of chain needed for your application. You will

be required to remove excess links with bolt cutters.

Proceed to pass the FIXTURE WIRES, GROUND WIRES and SAFETY

LOOP at the top of the FIXTURE with a QUICK-LINK CONNECTOR.

2 . With your fixture still not mounted yet, proceed to unravel the FIXTURE

WIRES, GROUND WIRE and the SAFETY CABLE.

Locate the FIXTURE CHAIN and attach one end of it to the FIXTURE

top side of the PIPE and hand tighten until the coupling touches

the top inside of the outlet box. Now install the cotter pin.

in the outlet box and the structural member. Install the LARGE

FLAT WASHER, LOCK WASHER AND LARGE HEXNUT onto the

A 5/8” diameter clearance hole must be drilled on the top inside

center of the OUTLET BOX AND THROUGH THE STRUCTURAL

SUPPORT MEMBER. Slip the PIPE up through the clearance hole

ACTUAL WEIGHT OF THE FIXTURE.

the fixture weight.

STRUCTURAL OR BRIDGING MEMBER SUPPORT 4 TIMES THE

Note: the opposite end of the PIPE must be attached to a

structural or bridging member of sufficient strength to support

3/8-18 NPSM PIPE to the HEX COUPLING until it is visible in the

side hole opening. (Note that the PIPE has a cotter pin hole on

one end, do not thread that end into the HEX COUPLING).

Tighten the SET SCREW which will lock the pipe in place.

supported by a 3/8-18 NPSM PIPE (supplied). Assemble the

1 .

INDEPENDENT of the OUTLET BOX. This fixture must b

The weight of this fixture will require a means of support

CEILING INSTALLATIONINSTRUCTIONS

FOR FIXTURES WEIGHING OVER 45 LBS.

thread the CANOPY CHAIN LOOP into the bottom of the NIPPLE.

NOTE: IT IS RECOMMENDED THAT THE

NOTE: DO

+ 1 hidden pages