6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
. .
, .
INSTRUCTION SHEET IS TF1041: STYLE NUMBER TF1041EP:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
!
Hex Nut for Mounting Screw( )
WARNINGS AND CAUTIONS
Description
Crossbar
Green Ground Screw
Mounting Screws
Lock Washer
Mounting Ball
CenterStem
Finial
Fixture Body
Shade
Quantity
1pc
1pc
2pcs
2pcs
2pcs
2pcs
1pc
1pc
1pc
1pc
ISSUED 09-2008
A
B
C
D
E
F
G
H
I
J
WARNING:
Before beginning the installation, turn off electricity atthe circuit breaker box or the main fuse box by
●
switching off the circuit breaker or removing the fuse.
CAUTION:
These instructions are provided for your safety.It is very important that they are read completely before the
●
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
●
sufficient time to cool down. DO NOT subject the lamp to any shock while litas shattering of lamp may result.
PREPARATION
Before beginning installation of product, make sure all parts are present. Compare parts with package
●
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
EstimatedAssembly Time : 15 30 minutes
●
Tools Required forAssembly (not included) : Flathead Screwdriver Phillips Screwdriver, Pliers,
●
Electrical Tape, Wire Cutters, Safety Glasses &2, 100 Watt, Type -A Medium Base Bulbs.
Helpful Tools (not included) : Wire Strippers.
●
INSTALLATION INSTRUCTIONS
STEP 1:
a Screw the Mounting Screws into the Crossbar place the
. ,
Lock Washers over the Mounting Screws and thread the
Hex Nuts onto the Mounting Screws as shown Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar
b Secure the Crossbar to the Outlet Box with Outlet Box
.
Screws
.
.
,
Mounting Screw
Crossbar
Hex Nut
.
Lock Washer
1 OF 3
Outlet Box
Outlet Box Screw
INSTALLATION INSTRUCTIONS
STEP 2:
a Locate the Fixture Canopy onto the Crossbar and slip the
.
Button Stop on the end of Lanyard into the Slot on the
Crossbar as shown.
STEP 3:
* ( )
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
. ( )
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
. ( )
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
( ) .
carefully stuff all of the connected wires into the Outlet Box
( )
STYLE NUMBER TF1041EP:
ButtonStop
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE( )
FROM HOUSE
GROUND WIRE GROUND WIRE
.
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Crossbar
Slot
Lanyard
Fixture Canopy
STEP 4 :
a Place the Ceiling Canopy onto Outlet Box aligning 2
.
holes in the Ceiling Canopy with 2 Mounting screws
threaded on the Crossbar and secure it against wall with
Mounting Balls
.
STEP 5:
a Thread the beaded end of the Center Stem into the
.
Coupling underside of the Socket Cluster. Hand tighten
until snug.
Coupling
Outlet Box
Mounting Screw
Ceiling Canopy
Mounting Ball
SocketCluster
CenterStem
2 OF 3