6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-TCA5009
STYLE NUMBER: TCA5009VP
PACKAGE CONTENTS
PART
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
DESCRIPTION
Green Ground Screw
Hex Nut
Nipple
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Decorative Candle Cover
Lock Screw
5 Beads with H63mm Crystal
Fixture Loop
Beads Chain
Fixture Assembly
Bottom Assembly
QUANTITY
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
9pcs
6pcs
6pcs
1pc
6pcs
1pc
1pc
ISSUED 09-2010 REVISED 2010-11-30
A
B
C
D
E
F
G
H
I
J
K
M
N
O
Repl. Beads and Crystals
a) 6 Beads with H63mm Crystal
[1pc]
b) 5 Beads with H63mm Crystal
[1pc]
c) 4 Beads with H63mm Crystal
[1pc]
d) 3 Beads with H63mm Crystal
[1pc]
e) 2 Beads with H63mm Crystal
[1pc]
Q
f) H32mm Crystal [1pc]
g) 1 Bead with H38mm Crystal
[1pc]
h) 2 Beads with H38mm Crystal
[1pc]
i) 3 Beads with H38mm Crystal
[1pc]
j) 4 Beads with H38mm Crystal
[1pc]
k) 1 Bead with H32mm Crystal
[1pc]
l) 2 Beads with H32mm Crystal
[1pc]
1pc
L
Q - Replacement Beads and Crystals
a)
f)
k)
b)
g)
l)
h)
P
c)
d)
i)
e)
j)
1OF6
WARNINGS AND CAUTIONS
STYLE NUMBER: TCA5009VP
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (9) 60W B10 candelabra base bulbs
.
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Thread the Fixture Loop onto the nipple on the top
center of the Fixture Assembly. Hand-tighten until
snug.
STEP 2:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug.
Fixture Loop
Fixture
Assembly
Outlet Box
Crossbar
Outlet Box
Screw
2OF6
PREPARATION
STEP 3:
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar.
c. Using pliers, thread the Hex Nut against the Crossbar
and hand-tighten until snug.
STEP 4:
a. Thread another Hex Nut onto the end of the Nipple.
b. Place the Lock Washer over the end of the Nipple and
then thread the Canopy Chain Loop onto the end of the
Nipple.
c. Using pliers, thread the Hex Nut against the Canopy
Chain Loop and hand-tighten until snug.
Crossbar
STYLE NUMBER: TCA5009VP
Lock Washer
Hex Nut
Nipple
Nipple
STEP 5:
a. Push the Ceiling Canopy upward over the Outlet Box.
Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling
Canopy.
Hex Nut
Lock Washer
Canopy Chain Loop
Outlet Box
Canopy Chain Loop
Ceiling Canopy
Canopy Lock Ring
3OF6
INSTALLATION INSTRUCTIONS
STEP 6:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed. You may need to use
pliers to open the chain links. If so, put a cloth over the
chain to protect the finish from the pliers.
b. Attach one end of the Fixture Chain onto the Canopy
Chain Loop and then attach the other end of the Fixture
Chain onto the Fixture Loop on the top of the fixture.
STYLE NUMBER: TCA5009VP
Canopy Chain Loop
Fixture Chain
Supply Wires
Fixture Loop
STEP 7:
a. Pull the Supply Wires up through the Fixture Chain
alternating links. Push the wires up through the Canopy
Chain Loop into the outlet box.
Canopy Chain Loop
Fixture Chain
Supply Wires
4OF6
INSTALLATION INSTRUCTIONS
STYLE NUMBER: TCA5009VP
STEP 8:
a. Un-thread the Canopy Lock Ring and slide Canopy
Lock Ring and Ceiling Canopy down the Fixture Chain.
b. Push all slack fixture wire through Canopy Chain Loop
into Outlet Box. Trim excess fixture wire leaving a
minimum of 6 in. Hanging out of the Outlet Box.
c. Refer to STEP 9 to connect the wires.
d. Re-attach the Ceiling Canopy as shown in STEP 5.
Outlet Box
Canopy Chain Loop
Fixture Chain
Ceiling Canopy
Canopy Lock Ring
STEP 9:
Use Wire Connectors to connect the wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
5OF6
INSTALLATION INSTRUCTIONS
STYLE NUMBER: TCA5009VP
STEP 10:
a. With another person holding the Bottom Assembly.
Attach the Arms on the Bottom Assembly to the
mounting holes underside of the Socket. Secure them
with the Lock Screws. Hang-tigthen until snug.
b. Attach the 5 Beads with H63mm Crystal to the hanger
at the Lock Screws.
c. Attach one end of the Beads Chain to the Hanger at the
bottom edge of the Junction Box. Attach the another
end of the Beads Chain to the Hangers at the scroll end
of the Support Arms.
Hanger
Support Arm
Junction Box
Beads Chain
Socket
Hanger
Arm
STEP 11:
a. Place the Decorative Candle Cover over the Candle
Cover as shown.
Lock Screw
5 Beads with
H63mm Crystal
Bottom
Assembly
Decorative Candle Cover
Candle Cover
STEP 12:
a. Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
6OF6
Loading...