Quoizel SMT1612BN User Manual
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS-SMT1612
STYLE NUMBER: XXSMT1612
PACKAGE CONTENTS
PART
A
B
C
D
E
F
G
H
I
DESCRIPTION
Crossbar
Green Ground Screw
Lock Washer
Hex Nut
Nipple
Flat Washer
Finial
Ceiling Canopy
Shade
QUANTITY
1pc
1pc
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
A
B
C
D
E
F
ISSUED 03-2011
G
H
I
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 15-20 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (1) 100W Type-A medium base bulb
● Helpful Tools (not included): Wire strippers.
1OF3
.
INSTALLATION INSTRUCTIONS
STEP 1:
a Locate the Crossbar and attach it to the Outlet Box
.
using the Outlet Box Screws not supplied
b Locate the Nipple and thread one Hex Nut onto it
.
().
about half way. Slip a Lock Washer onto it and thread
one end of the nipple into the center hole of the
Crossbar
c Position the Ceiling Canopy over the outlet box,
.
.
passing the mounting hole in the center of the Ceiling
Canopy over the end of Nipple
d Adjust the Nipple so approx 3 8 inch of the Nipple is
.
.
./"
protruding from the mounting hole. This adjustment
may take a few tries.
e When this length is achieved, remove the Ceiling
.
Canopy and tighten the Hex Nut up against the
underside of the Crossbar with pliers.
STEP 2:
a. Thread another Hex Nut onto the other end of the
nipple. Thread this Hex Nut on just enough so the
inside surface of the pan rests against it.
You may have to trial fit the Ceiling Canopy one more
times to insure this distance also. This Hex Nut is
needed here to prevent you from crushing down the
center of the Ceiling Canopy*.
Outlet Box
Screw
Hex Nut
Nipple
Ceiling Canopy
STYLE NUMBER: SMT1612XX
Outlet Box
Crossbar
Lock Washer
Ceiling Canopy
Nipple
Hex Nut
STEP 3:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
2OF3
WHITE OR RIBBED
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
FROM HOUSE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
Loading...