Quoizel QPP1775TC User Manual
Assembly Instruction Sheet #IS-QPP1775TC
For Style QPP1775TC
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended:
(1)23W CFLMaximum.
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
(1)Medium Base Decorative Filament 60Wbulb(supplied), Maximum 100W,Alternate bulb
20-30minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Ceiling
A
Canopy
x1
Socket
D
Assembly
x1
Figure 1
B
B
Supply Wires
and Ground Wire
A
C
C
6” Rod
B
x2
Bulb
E
C
12” Rod
x2
x1
Hardware Contents
Crossbar Assembly
STEP 1 Assemble the Rods and the Ceiling Canopy-
A. Determine the Rods (B/C) to be assembled to the Socket Assembly
(D) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Ceiling Canopy (A). Thread the Socket Assembly (D),
the chosen Rods (B/C) and the Ceiling Canopy (A) together. Hand
tighten until snug.
x1
AA
D
STEP 2 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (AA). Attach the
Crossbar Assembly (AA) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box Screws
(not included)
STEP 3 Fit Ceiling Canopy to
A.
-
Crossbar Assembly
Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Ceiling Canopy A to the
Crossbar Assembly (AA) and
secure with mounting balls.
Note: The ( )
should be snug against the
and the mounting balls. If
ceiling
()
Ceiling Canopy A
Figure 2
Outlet
Box
AA
Supply Wires
with Ground Wire
Figure 3
AA
Hex Nut and
A
Lock Washer
Mounting Screw
Mounting Ball
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
March2014
not, adjust the length of the nipple on the CrossbarAssembly (AA)
by unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
correct length is achieved. Once the Ceiling Canopy (A) is secure,
remove the mounting ball and Ceiling Canopy (A) and proceed to
Step 4.
STEP 4 Wire Connections-
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed Side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
Side Wire from Fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 5 Install Fixture Body-
A. Carefully tuck all wires into the outlet
box and position the Ceiling Canopy
(A) over the outlet box.Align the
holes in the Ceiling Canopy (A) with
the mounting screws, then attach the
Ceiling Canopy (A) using the
previously removed mounting balls.
Hand tighten until snug.
STEP 6 Install Bulb-
A. This fixture uses standard bulb 60W
(supplied) with a standard screw base.
Maximum 100 watts.
B. Insert bulb and screw properly into place.
Your fixture is now assembled and ready to
use. Enjoy!
A
Figure 5
AA
Mounting
Screw
Mounting Ball
Figure 6
Socket
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
QPP1775TC
FINISH: TUSCAN BROWN
Figure 4
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
2
1
5” Dia.
E
1”
53.5”
OVERALL HEIGHT
(2) 6” AND (2) 12” RODS
INCLUDED
(1)Medium Base
Decorative Filament
60W bulb (provided),
Maximum 100W.
PART NUMBER
NO.
9012EXTC
1
2
9006EXTC
3
I1101EC
2014 QuoizelInc.
3
NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
ROD EXT TUSCAN BROWN 12"L X 0.5"D
ROD EXT TUSCAN BROWN 6"L X 0.5"D
VINTAGE BULB 60W 1910 INCANDESCENT
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2of2
15”
7” Dia.
REQ.
2
2
1
March2014
Loading...