6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS QMC404STYLE NUMBER QMC404BO:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
Crossbar
Green Ground Screw
Hex Nut
Nipple
Lock Washer
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Ceiling Canopy
Fixture Assembly
Fixture Loop
Crystal Cluster
Crystal Pendant
Description
Quantity
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
1pc
1pc
4pcs
28pcs
ISSUED 03-2010
A
B
C
D
E
F
G
H
I
K
L
M
!
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 45 minutes
● Tools Required for Assembly (not included): Flathead screwdriver Phillips screwdriver, Pliers,
Electrical tape, Wire cutters, Safety glasses & (4) 60W B10 candelabra base bulbs.
● Helpful Tools (not included): Wire strippers.
J
,
1OF4
INSTALLATION INSTRUCTIONS
STEP 1:
a Thread the Fixture Loop onto the nipple on the top center of
.
the Fixture Assembly. Hand-tighten until snug.
STEP 2:
a Secure the Crossbar onto the Outlet Box with Outlet Box
.
Screws Tighten until snug
..
STYLE NUMBER QMC404BO:
Fixture Loop
Fixture Assembly
Outlet Box
Crossbar
Outlet Box
Screw
STEP 3:
Pliers is required on this step
*.
a Thread one Hex Nut onto top end of the Nipple
..
b Place one Lock Washer over the top end of the Nipple
.
and then thread the Nipple into the center lock hole of
the Crossbar
c Using pliers thread the Hex Nut against the crossbar
.,
and hand tighten until snug
d Thread another Hex Nut onto the bottom end of the
.
Nipple
.
.
.
Crossbar
Lock Washer
Hex Nut
Nipple
Hex Nut
2OF4
INSTALLATION INSTRUCTIONS
STYLE NUMBER QMC404BO:
STEP 4
a Adjust the Fixture Chain to your desired length by
.
removing the links if needed
*,
you might be required to use chain pliers to spread links
open
b Pull the supply wires through the Fixture Chain alternating
.
links And then pull the wires through the following
components in turn
Canopy Lock Ring Ceiling Canopy Canopy Chain Loop,
Lock Washer and Nipple
c Place Lock Washer over the end of the Nipple and thread
.
the Canopy Chain Loop onto the end of the Nipple
d Using plier thread the Hex Nut against the Canopy Chain
.,
Loop and tighten until snug
e Attach one end of the Fixture Chain onto the Fixture Loop
.
:
.
Please note that depends on chain material thickness
.
.
:
,,
,.
.
.
Nipple
Hex Nut
Lock Washer
Canopy Chain Loop
Ceiling
Canopy
and attach the another end of the chain onto the Canopy
Chain Loop
f Refer to Step 5 Wire Connections to connect wires
.- .
g Push the Ceiling Canopy upward over the Outlet Box
..
h Thread the Canopy Lock Ring onto the Canopy Chain Loop
.
and tighten until snug to secure the Ceiling Canopy
.
Fixture Chain
.
Canopy Lock Ring
Fixture Loop
STEP 5:
*()
Use Wire Connectors not supplied to connect the
.
wires
.
a Connect the House Ground Wire to the Fixture Ground
Wire.
.()
b Connect the House White or Ribbed Wire to the
Fixture Supply Wire White or Ribbed Side .
.()
c Connect the House Black or Red Wire to the Fixture
Supply Wire Black or Smooth Side
.
d Wrap each connection with approved electrical tape and
().
()
carefully stuff all of the connected wires into the Outlet
.
Box
WHITE OR RIBBED
FROM HOUSE
BLACK OR RED WIRE()
FROM HOUSE
GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
3OF4
INSTALLATION INSTRUCTIONS
STEP 6:
..a Attach the small end of the Crystal Cluster into the pin hole
on the bottom of the Upper Stamping. Attach the another end
of the Crystal Cluster into the pin hole on the top edge of the
Bottom Stamping.
b Attach the Crystal Pendants onto the hangers on the Support
Arms, hangers on the bottom of the Bobeches and pin holes
on the bottom of the Bottom Stamping.
STYLE NUMBER QMC404BO:
Upper Stamping
Crystal Cluster
Bobeche
Hanger
Pin Holes
Bottom
Stamping
STEP 7:
.a Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
Crystal
Pendant
Hanger
4OF4
Loading...