Drop [4 pcs]
B) - Crystal Cluster [4 pcs]
C) - Crystal Bobeche [4 pcs]
D) - Crystal Drop A [4 pcs]
E) - Crystal Drop B [4 pcs]
F) - Crystal Finial [1 pc]
QUANTITY
1pc
1pc
2pcs
1pc
2pcs
1pc
1pc
1pc
1pc
4pcs
4pcs
1pc
1pc
4pcs
1pc
1pc
REVISED 2010-04-19
A
B
C
D
E
F
G
H
I
J
K
P:
A)
L
M
N
O
C)
D)
B)
E)
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb9s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
1OF6
F)
Page 2
PREPARATION
STYLE NUMBER: QMC402RL
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (4) 60W B10 candelabra base bulbs
.
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Screw the beaded end of the Center Rod Assembly into
the Coupling on the top center of the Socket Assembly.
Please line up Mounting Holes on the side of the Center
Rod Assembly and the Tabs at the top edge of the Ring
before tighten them together until snug.
b. Thread the Fixture Loop onto the nipple on the top
center of the Center Rod Assembly. Hand-tighten until
snug.
Fixture Loop
Mounting Hole
Tab
Center Rod
Assembly
Ring
Coupling
Socket
Assembly
2OF6
Page 3
INSTALLATION INSTRUCTIONS
STEP 2:
a. Locate the Side Arms. Line up the holes on the Side
Arm onto the mounting holes on the side of the Center
Rod Assembly and the Tabs at the top edge of the Ring.
Thread the Lock Screws into the mounting holes to
secure it. Hand-tighten until snug.
Center Rod
Assembly
STYLE NUMBER: QMC402RL
Lock
Screw
Side Arm
Lock
Screw
Tab
Ring
STEP 3:
a. Thread the Crystal Finial onto the nipple on the bottom
center of the Socket Assembly. Hand-tighten until
snug.
STEP 4:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug.
Socket
Assembly
Crystal Finial
Outlet Box
Crossbar
Outlet Box
Screw
3OF6
Page 4
INSTALLATION INSTRUCTIONS
STEP 5:
Pliers is required on this step.
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar.
c. Using pliers, thread the Hex Nut against the Crossbar
and hand-tighten until snug.
d. Thread another Hex Nut onto the bottom end of the
Nipple.
STEP 6:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed.
Please note that depends on chain material
thickness, you might be required to use chain pliers to
spread links open.
b. Pull the supply wires through the Fixture Chain
alternating links. And then pull the wires through the
following components in turn:
Canopy Lock Ring, Ceiling Canopy, Canopy Chain
Loop, Lock Washer, and Nipple.
c. Place Lock Washer over the end of the Nipple and
thread the Canopy Chain Loop onto the end of the
Nipple.
d. Using pliers, thread the Hex Nut against the Canopy
Chain Loop and tighten until snug.
e. Attach one end of the Fixture Chain onto the Fixture
Loop and attach the another end of the chain onto the
Canopy Chain Loop.
f. Refer to STEP 7 - Wire Connections to connect wires.
g. Push the Ceiling Canopy upward over the Outlet Box.
h. Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling
Canopy.
Crossbar
Nipple
Lock Washer
STYLE NUMBER: QMC402RL
Lock Washer
Hex Nut
Nipple
Hex Nut
Hex Nut
Canopy Chain Loop
Ceiling
Canopy
Fixture Chain
Canopy Lock Ring
4OF6
Fixture Loop
Page 5
INSTALLATION INSTRUCTIONS
STEP 7:
Use Wire Connectors (not supplied) to connect the
wires.
a. Connect the House Ground Wire to the Fixture Ground
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box.
STEP 8:
a. Attach one end of the Crystal Cluster with Crystal Drop
to the Hanger on the Side Arm. Attach the another end
of the Crystal Cluster with Crystal Drop to the Hanger
on the next Side Arm.
b.
Attach one end of the Crystal Cluster to the Hanger on
Bottom
theArm. Attach the another end of the Crystal
Cluster to the Hanger on the nextArm.
c. Attach Crystal Drop A to the Hanger on the top end of
the Side Arm.
d. Attach the Crystal Drop B to the Hanger on the end of
the Support Arm.
Bottom
WHITE OR RIBBED
FROM HOUSE
BLACK (OR RED) WIRE
FROM HOUSE
GROUND WIRE
FROM HOUSE
STYLE NUMBER: QMC402RL
WHITE OR RIBBED
FROM FIXTURE
BLACK OR SMOOTH
FROM FIXTURE
GROUND WIRE
FROM FIXTURE
Hanger
Crystal Drop A
Hanger
Crystal Cluster
with Crystal Drop
Support
Arm
Crystal Cluster
Bottom Arm
Side Arm
Hanger
Hanger
Crystal Drop B
5OF6
Page 6
INSTALLATION INSTRUCTIONS
STEP 9:
a. Place the Crystal Bobeche and the Candle Cover over
the Socket as shown.
STYLE NUMBER: QMC402RL
Candle Cover
Crystal Bobeche
Socket
STEP 10:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
6OF6
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.