Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters,wire
Quoizel, Inc.
strippers,electrical tape, safetyglasses.
6 Corporate Parkway
Goose Creek, SC
29445
BulbRecommended: (5)Candelabra Base 60WMaximum
EstimatedAssemblyTime:30-45 minutes
Preparation:Identify and inspectallparts before beginninginstallation.Check package
Customer Service
Phone 631.273.2700
Fax 631.231.7102
contentlist and diagramsbelowto be sureallparts are present.Ifany parts aremissing
ordamaged, do notattemptto assemble, install,oroperate the fixture.Contactcustomer
servicefor replacement parts.
www.quoizel.com
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc.
Thank youfor purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of8
May2012
Page 2
QMC1199FR
FINISH: FRENCH BRONZE
SOCKET ORIENTATION
Overall Height 120.5”
(Includes 96” Chain)
24.5”
1”
5.5” Dia.
2
13
6
NOTE: TWO LIGHTS SHOWN
FOR ILLUSTRATION
PURPOSES ONLY.
1
(5)60W Candelabra
base bulbs
(not Supplied)
PART NUMBER
NO.
M2302CCFR
1
2
M2301CHFR
3
4
5
6
G3217CR
G3218CR
G3219CR
G3220CR
7
12
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
CANDLE COVER 0.875"D X 3.75"H
CHAIN FRENCH BRONZE 3.8MM X4'
DECORATIVE CRYSTAL 30MM X 2.17
DECORATIVE CRYSTAL 30MM X 2.91
DECORATIVE CRYSTAL 30MM X 3.42
DECORATIVE CRYSTAL 35MM X 3.13
4
3
5
8
9
10
11
18” Dia.
REQ.
5
1
5
20
5
5
7
8
9
10
11
12
13
G3221CR
G3222CR
G3223CR
G3224CR
G3225CR
M2303FIFR
9516KIT
DECORATIVE CRYSTAL 35MM X 3.76
DECORATIVE CRYSTAL 35MM X 4.39
DECORATIVE CRYSTAL 35MM X 5"L
DECORATIVE CRYSTAL 35MM X 5"L
DECORATIVE CRYSTAL 40MM X 4.41
FINIAL 0.83"D X 0.82"H
MOUNTING HARDWARE/CANOPY FRENCH BRONZE 5.5"D
2of8
5
5
5
5
1
1
1
Page 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Package Contents
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
A
F
G
Part
A Crossbar
B
C
D
E
F
G
H
I
J
K
L
M
N
O
Description
Nipple
Lock Washer
Hex Nut
Ceiling Canopy
Canopy Chain Loop
Canopy Lock Ring
Fixture Chain
Fixture Loop
Center Rod Assembly
Socket Assembly
(1) 40mm ball + (4) 12mm
balls with hook
(1) 36mm ball + (5) 12mm
balls with hook
(1) 36mm ball + (5) 12mm
balls with ring clip
(1) 36mm ball + (4) 12mm
balls with ring clip
Quantity
1pc.
1pc.
2 pcs.
2 pcs.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
1pc.
5 pcs.
5 pcs.
5 pcs.
B
C
I
D
E
K
H
J
P
Q
R
S
T
2012 QuoizelInc. May2012
(1) 36mm ball + (3) 12mm
balls with ring clip
(1) 36mm ball + (2) 12mm
balls with ring clip
(1) 30mm ball + (3) 12mm
balls with ring clip
(1) 30mm ball + (2) 12mm
balls with hook
(1) 30mm ball + (1) 12mm
ball with ring clip
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
5 pcs.
10 pcs.
5 pcs.
20 pcs.
5 pcs.
3of8
L
M
P
Q
R
N
S
O
T
Page 4
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
STEP 1 - Assemble Center Rod Assembly and
Socket Assembly
A. Unfold Support Arms on the Socket Assembly (K) to
proper locations.
B. Thread the bottom end of the Center Rod Assembly (J)
onto the nipple on the top center of the Socket
Assembly (K) as shown. Hand tighten until snug.
STEP 2 - Assemble Fixture Loop
Figure 1
Socket
Assembly
Support Arm
Figure 2
Center Rod
Assembly
Fixture Loop
A. Thread the Fixture Loop (I) onto the nipple on the top
end of the Center Rod Assembly (J) as shown. Hand
tighten until snug.
STEP 3 - Attach Crossbar to Outlet Box
A. Secure the Crossbar (A) to the outlet box with outlet
box screws (not supplied). Tighten until snug.
Mounting
Hole
Center Rod
Assembly
Outlet Box
Crossbar
Outlet Box
Screw (not
Supplied)
Figure 3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc. May2012
or visit us on-line at www.quoizel.com
4of8
Page 5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
STEP 4 Attach Nipple to Crossbar-
A. Thread one Hex Nut (D) onto the top end of the Nipple
(B).
B. Place one Lock Washer (C) over the top end of the
Nipple (B) and then thread the Nipple (B) into the center
lock hole of the Crossbar (A).
C. Using pliers, thread the Hex Nut (D) against the
Crossbar (A) and hand tighten until snug.
Crossbar
Lock Washer
Hex Nut
Nipple
Figure 4
STEP 5 - Attach Canopy Chain Loop to Nipple
A. Thread another Hex Nut (D) onto the end of the Nipple
(B).
B. Place the Lock Washer (C) over the end of the Nipple
(B) and then thread the Canopy Chain Loop (F) onto the
end of the Nipple (B).
C. Using pliers, thread the Hex Nut (D) against the
Canopy Chain Loop (F) and hand tighten until snug.
STEP 6 Assemble Ceiling Canopy-
A. Push the Ceiling Canopy (E) upward over the Outlet
Box. Thread the Canopy Lock Ring (G) onto the Canopy
Chain Loop (F) and tighten until snug to secure the
Ceiling Canopy (E).
Outlet Box
Nipple
Crossbar
Hex Nut
Lock Washer
Canopy
Chain Loop
Figure 5
Outlet Box
Canopy Chian Loop
Ceiling Canopy
Canopy
Lock Ring
Figure 6
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc. May2012
or visit us on-line at www.quoizel.com
5of8
Page 6
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
STEP 7 Attach Fixture Chain to Canopy
-
Chain Loop and Fixture Loop
A. Adjust the Fixture Chain (H) to your desired length by
removing the links if needed. You may need to use plier
to open the chain links. If so, put a cloth over the chain
to protect the finish from the pliers.
B. Attach one end of the Fixture Chain (H) onto the
Canopy Chain Loop (F) and then attach the other end of
the Fixture Chain (H) onto the Fixture Loop (I) on the
top of the fixture.
STEP 8 Pass Supply Wires through Fixture
-
Chain
A. Pull the Supply Wires and Ground Wire up through the
Fixture Chain (H) alternating links. Push the wires up
through the Canopy Chain Loop (F) into the outlet box.
Fixture Loop
Canopy Chain Loop
Fixture Chain
Supply Wire and
Ground Wire
Figure 7
Canopy Chain
Loop
Fixture Chain
Supply Wire
and Ground Wire
Figure 8
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc. May2012
or visit us on-line at www.quoizel.com
6of8
Page 7
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
STEP 9 - Make Wire Connections
A. Un-thread the Canopy Lock Ring (G) and slide Canopy Lock
Ring (G) and Ceiling Canopy (E) down the Fixture Chain (H).
B. Push all slack fixture wire through Canopy Chain Loop (F)
into Outlet Box. Trim excess fixture wire leaving a minimum
of 6 inch. Hanging out of the Outlet Box.
C. Use standard wire connectors to make all wire connections.
(Connectors are not included with fixture.) Strip and prepare
wire ends according to instructions supplied with connectors.
D. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
E. Connect Black (or Red) Supply Wire from the Outlet Box to
Black Wire from fixture.
F. Connect Ground Wire from the Outlet Box to Ground Wire
from fixture.
G. Twist connectors until wires are tightly joined together.
H. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
G. Re-attach the Ceiling Canopy (E) as shown in Step 6.
Supply Wire
and Ground
Wire from
Outlet Box
Supply Wire and
Ground Wire
Canopy Chain Loop
Fixture Chain
Ceiling
Canopy
Canopy Lock Ring
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Ground wire from supply Ground wire from fixture
Black wire from fixture
Figure 10
Figure 9
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc. May2012
or visit us on-line at www.quoizel.com
7of8
Page 8
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QMC1199FR
For Style QMC1199FR
STEP 10 Attach Glass Beads-
A. Attach (1) 40mm Ball + (4) 12mm Balls with Hook
(L) to the hanger on the bottom center of the
fixture.
B. Attach (1) 36mm ball + (5) 12mm Balls with Hook
(M) to the hangers on the side of the Junction Box.
C. Place (1) 36mm Ball + (5) 12mm Balls with Ring
Clip (N), (1) 36mm Ball + (4) 12mm Balls with Ring
Clip (O), (1) 30mm Ball + (3) 12mm Balls with Ring
Clip (R) and (1) 30mm Ball + (1) 12mm Ball with
Ring Clip (T) to the scrolls on the SupportArm as
shown.
D. Attach (1) 30mm Ball + (2) 12mm Balls with Hook
(S) to hangers on the side of the Cup.
E. Place (1) 36mm Ball + (3) 12mm Balls with Ring
Clip (P) to the scroll end of the SideArms on the
Junction Box.
F. Place (1) 36mm Ball + (2) 12mm Balls with Ring
Clip (Q) to the scroll ends of Side Arms on the side
of the Center RodAssembly.
(1) 36mm ball +
(3) 12mm balls with
ring clip
Center Rod
Assembly
Side Arm
Junction Box
(1) 36mm ball +
(5) 12mm balls
with hook
(1) 40mm ball +
(4) 12mm balls
with hook
(1) 36mm ball + (5) 12mm
balls with ring clip
Figure 11
(1) 36mm ball +
(2) 12mm balls with
ring clip
Cup
Support Arm
(1) 30mm ball
+ (3) 12mm
balls with ring
clip
(1) 30mm ball
+ (1) 12mm ball
with ring clip
(1) 30mm ball +
(2) 12mm balls
with hook
(1) 36mm ball +
(4) 12mm balls
with ring clip
STEP 11 Install Bulb-
A. This fixture uses candelabra bulb with candelabra screw
base. Maximum 60 watts.
B. Insert bulb and screw properly into place.
Your lamp chandelier fixture is now assembled and ready
to use. Enjoy!
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2012 QuoizelInc. May2012
or visit us on-line at www.quoizel.com
8of8
Bulb
Socket
Figure 12
Loading...