Quoizel QF1778SBN User Manual
Assembly Instruction Sheet #IS-QF1778S
For Styles QF1778SBN and QF1778SPN
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax 631.231.7102
www.quoizel.com
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,
safetyglasses.
BulbRecommended:
EstimatedAssembly Time:
Preparation:
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.
Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
(3)Medium Base 100W bulb, Alternate bulb (3) 23WCFLMaximum.
30-45minutes
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Fixture Body
A
x1
Hardware Contents
CC
B
Socket
C
Collar
x3
Hex Nut
x1
Shade
x3
Nipple (DD). Thread the Lock Ball (EE) onto the Nipple (DD). Adjust
the Nipple (DD) to allow the backplate of the Fixture Body (A) to rest
against the wall surface when held in place by the Lock Ball (EE).
D. Remove the Lock Ball (EE) and the Fixture Body (A). Tighten the
Hex Nut (CC) against the Crossbar (AA) to secure in place.
BB
AA
A
CC
DD
Nipple
Crossbar
AA
x1
Lock Washer
BB
x1
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Outlet Box Screw
(not included)
STEP 2 Install Nipple-
* Pliers is required for this step.
A. Thread the Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Place the Lock Washer (BB) over the Nipple
(DD) and then thread the Nipple (DD) into the Crossbar (AA) until the
Nipple (DD) is about 0.375” above the Crossbar (AA).
B. Place the backplate of the Fixture Body (A) over the Nipple (DD)
against the wall surface to determine the correct position of the
AA
Green
Ground
Screw
DD
x1
Lock Ball
EE
x1
Outlet Box
Figure 1
EE
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
Black wire from
supply (or Red)
Ground wire
from supply
Figure 3
Ribbed side wire
from fixture
Smooth side wire
from fixture
Ground wire
from fixture
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of2
March2014
STEP 4 Install Fixture Body-
STEP 5 Install Shade-
A. Carefully tuck all wires into the outlet box and position the backplate
of Fixture Body (A) over the outlet box. Pass the Nipple (CC)
through the holes on the backplate of the Fixture Body (A). Place
caulk (not supplied) into the previously removed Lock Ball (EE) and
then attach Fixture Body (A) using the Lock Ball (EE). Hand tighten
until snug.
A
CC
EE
Figure 4
QF1778SBN/QF1778SPN
FINISH: BRUSHED NICKEL/PALLADIAN BRONZE
1
A. Place Shade (B) over the
Socket, secure by threading
Socket Collar (C) onto the
Socket, hand tighten until sung.
STEP 6 - Install Bulb
A. This fixture uses standard bulb with
medium base. Maximum 100 watts.
B. Insert bulb and screw snugly into
place.
Note: Please be aware of that the
swivel can only be adjust outward
as indicated in illustration.
Your fixture is now assembled and
ready to use. Enjoy!
10” Dia.
1”
9”
5”
Socket
B
C
Figure 5
Figure 6
Socket
Bulb
5” Dia.
13” Dia.
(3)Medium Base
100W bulb
(not supplied)
PART NUMBER
NO.
G3821SH SHADE OPAL ETCHED GLASS 5"D 3
1
1 G3822SH SHADE CHAMPAGE MARBLE GLASS 5" 3
NOTE: ALL DIMENSIONS ARE ROUNDED UPTO THE NEAREST 1/2"
REPLACEMENT PART DESCRIPTION
REQ.
ITEM NUMBER
QF1778SBN
QF1778SPN
2014 QuoizelInc.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
2of2
March2014
Loading...