Quoizel QF1777BN User Manual

Assembly Instruction Sheet #IS-QF1777

6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com

..

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445

Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.

,.

For Styles QF1777BN and QF1777WT

ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters, wire strippers, electricaltape,

safetyglasses.

BulbRecommended:
EstimatedAssembly Time:
Preparation:

Identifyand inspect all parts beforebeginninginstallation. Check package content listand diagrams
belowto be sure all partsarepresent. If any parts aremissing or damaged, do not attemptto assemble, install, or
operatethe fixture. Contact customer serviceforreplacement parts.

(3)Candelabra Base 40W Maximum, Alternate bulb (3) 13WCFL

30-45minutes

Package Contents

Fixture Loop

A

x1

Stem

B

x1

Ring

C

x1

STEP 1 Install Fixture Loop, Stem and

A. Thread Stem (B) into the Swivel on the

B. Thread the end of the Stem (B) into the

-

Socket Assembly together

bottom of Fixture Loop (A). Hand tighten
until sung.

coupling on the top center of the Socket
Assembly (E) and hand tighten until snug.

Figure 1

Lock Screw

D

x3

E

Socket
Assembly
x1

Shade

F

x1

A

B

E

Hardware Contents

Canopy Chain Loop

EE

x1

Canopy Lock Ring

FF

x1

Fixture Chain

GG

x1

Quick Link

HH

x2

Ceiling Canopy

II

x1

28mm 12Ga28mm 12Ga

GND

Lock Washer

BB

x2

CC

DD

R

AA

Hex Nut
x2

Nipple
x1

Crossbar
x1

STEP 2 Install Crossbar-

A. AA)Attach the Crossbar ( to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..

Outlet Box

AA

Outlet Box Screw
(not included)

Green Ground Screw

Figure 2

STEP 3 Install Canopy Chain Loop and Nipple-

* Pliers is required for this step.

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)
is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

2014 Quoizel Inc.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

Thank you for purchasing a Quoizel product.

or visit us on-line at www.quoizel.com

1of3

March2014

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to
rest against the ceiling when held in place by the Canopy Lock Ring
(FF).

D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).

Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.

Supply Wires

and Ground Wire

DD

EE

HH

GG

AA

DD

BB

CC

EE

FF

CC

BB

Step B

Step A

II

Figure 3

STEP 4 - Install Fixture Chain and Ceiling Canopy

A. Adjust the Fixture Chain (GG) to your desired length by removing

the links if needed.

*

Pliers is required for this step.

B. With the Fixture Chain (GG) not attached to the Fixture Loop (A)

and the Canopy Chain Loop (EE), pull the supply wires through the
Fixture Chain (GG) alternating links.After the wires are through the
Fixture Chain (GG), pull the Supply Wires and the Ground Wire
through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in
order.

C. Attach one end of the Fixture Chain (GG) to the Fixture Loop (A)

with one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up
And Attach the other end of the Fixture Chain (GG) onto the Canopy
Chain Loop (EE) with another Quick Link (HH). The fixture will
nowhang safely. Close the chain loop at the Ceiling Canopy Loop
(EE).

D. Feed the Supply Wires and Ground Wire through the Canopy Chain

Loop (EE) and Nipple (DD) into the Outlet Box. Cut the wires

leaving approximately 8” of wire extending from the Outlet Box.
E. Refer to Step 6 for wire connections.
F. Raise the Ceiling Canopy (II) and Canopy Lock Ring (FF) up the

Fixture Chain (GG) and over the Canopy Chain Loop (EE). Tighten

the Canopy Lock Ring (FF) onto the Canopy Chain Loop (EE) until

tight.

Suggested chain length for Ceiling height :

8’ ceiling : use 5 link of chain and 2 quick links

9’ ceiling : use 15 links of chain and 2 quick links

10’ ceiling : use 25 links of chain and 2 quick links

II

FF

HH

A

Figure 4

STEP 5 - Wire Connections

A. Use standard wire connectors (not included) to make all wire

connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.

B. Connect White Supply Wire from the Outlet Box to Ribbed side

Wire from fixture.

C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth

side Wire from fixture.

D. Connect Ground Wire from the Outlet Box to Ground Wire from

fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

White wire

from supply

Black wire from
supply (or Red)

Ground wire

from supply

Figure 5

STEP 6 Install Ring-

A. Attach the Side Chains of the Ring (C) to

the Hooks on the side of the Fixture Chain

Ribbed side wire
from fixture

Smooth side wire
from fixture

Ground wire
from fixture

A

Hook

Assembly (A).

2014 Quoizel Inc.

Figure 6

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2of3

Side
Chain

C

March2014