Preparation:Identifyandinspect all partsbeforebeginninginstallation. Check package
contentlistanddiagrams below tobesureall parts arepresent.Ifany parts aremissing
ordamaged,donot attempt toassemble,install,or operate thefixture.Contactcustomer
serviceforreplacementparts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
A
Package Contents
Part
ACrossbar
B
C
D
E
F
G
H
I
Description
Mounting Screw
Lock Washer
Hex Nut
Mounting Ball
Lock screw
Socket Assembly
Shade
Shade Holder
Quantity
1pc.
2 pcs.
2 pcs.
2 pcs.
2 pcs.
3 pcs.
1pc.
1pc.
1pc.
B
C
D
E
G
H
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
F
Thank you for purchasing a Quoizel product.
or visit us on-line at www.quoizel.com
1of5
I
September2011
QF1201SWT
FINISH: WESTERN BRONZE
25" Dia.
6” Dia.
GND
1"
2.4mm
13Ga
QUOIZEL
R
12”
(4)100W A19
Medium Base Bulbs
(Not Supplied)
1
5”
21” Dia.
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
PART NUMBER
NO.
G2975SHSHADE ETCHED W/PNTD WHTE INSID
1
REPLACEMENT PART DESCRIPTION
2
REQ.
1pc.
2of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
STEP 1Adjust Fixture Assembly-
,.
Assembly Instruction Sheet #IS-QF1201SWT
For Style QF1201SWT
A. Unfold support arms on fixture assembly to proper
locations.
STEP 2 - Attach Mounting Screws, Lock
Washers and Hex Nuts to Crossbar
A. Line up a set of holes on the Crossbar (A) and Holes on
the Ceiling Canopy of the Socket Assembly (G).
B. Thread Mounting Screws (B) into the holes on the
Crossbar (A), pass Lock Washers (C) and thread Hex Nut
(D) onto the Mounting Screws (B). Hand tighten until
snug.
Figure 2
Mounting Screw
Lock Washer
Ceiling
Canopy
Figure 1
Crossbar
Hex Nut
Socket
Assembly
STEP 3 - Attach Crossbar to Outlet Box
A. Attach the Crossbar (A) to Outlet Box and secure by
threading Outlet Box Screws (not supplied) into the
Mounting Holes on the Outlet Box. Tighten until snug.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
or visit us on-line at www.quoizel.com
Figure 3
Outlet
Box
Crossbar
Mounting
Hole
Outlet Box
Screw
September2011
3of5
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QF1201SWT
For Style QF1201SWT
STEP 4Attach Lanyard-
A. The purpose of the lanyard is to provide the installer a
means to support the fixture from the junction box while
connecting the electrical wires. This enables the fixture
to hang from the junction box and your hands are free to
make the wire connections.
B. TurntheButtonStopsoitmaybeinsertedintothe
crossbar slot. Make sure the Button Stop is completely
inside the crossbar. Slowly release the fixture to make
sure it is supported by the Button Stop. Proceed to the
wiring steps. Once you are complete with the wiring
there is nothing to do with Lanyard. The Lanyard will
push into the junction box when the fixture is placed for
final mounting.
Crossbar
Slot
Button Stop
Lanyard
Figure 4
STEP 5Make Wire Connections-
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to White
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box
to Black Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire from supplyWhite wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Figure 6
Ground wire from supplyGround wire from fixture
Figure 5
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
or visit us on-line at www.quoizel.com
4of5
September2011
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
Assembly Instruction Sheet #IS-QF1201SWT
For Style QF1201SWT
STEP 6 - Attach Ceiling Canopy to Mounting
Screw
A. Place the Ceiling Canopy on the Socket Assembly (G)
over the Mounting Screws (B) and secure with Mounting
Balls (E). Hand tighten until snug.
STEP 7Attach Shade to Fixture Body-
A. Place Shade(H) inside Shade Holder(I).
B. Lift the Shade Holder (I) with shade (H) upward and
align rings of the Shade Holder (I) with the ends of the
Side Arms of the Socket Assembly (G).
C. Pass Lock Screws (F) through Tab of the Shade Holder
(I) and thread into Side Arm of the Fixture Body (A).
Hand tighten until snug
.
Mounting Screw
Socket Assembly
Fixture Body
Shade
Figure 7
Ceiling Canopy
Mounting
Ball
Figure 8
Side Arm
Tab
Shade Holder
STEP 8Install Bulb-
A. This fixture uses standard bulb with a standard screw base.
Maximum 100 watts.
B. Insert bulb and screw properly into place.
Your lamp semi-flush fixture is now assembled and ready to
use. Enjoy!
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
2011 Quoizel Inc.
or visit us on-line at www.quoizel.com
5of5
Lock Screw
Bulb
Socket
Figure 9
September2011
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.