Page 1
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
..
,.
INSTRUCTION SHEET IS Q611STYLE NUMBER Q611F:
PACKAGE CONTENTS
Part
A
B
C
D
E
F
G
H
I
J
K
L
M
Upper Assembly
Medium Assembly with Stem
Base Assembly with Stem
Shade
Diffuser
Finial
Check Ring
Spacer Tube
Nipple with Hex Nut
Washer
Rubber Washer
Hex Nut
Wrench
Description
Quantity
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
1pc
ISSUED 06-2009
D
A
E
B
F
I
G
J
!
CAUTIONS
These instructions are provided for your safety. It is very important that they are read completely
●
before the installation of your fixture. We strongly recommend that a professional electrician install the
fixture.
●
Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate
the product. Contact customer service for replacement part.
●
Estimated Assembly Time : 15 30 minutes
●
Tools Required for Assembly (not included) : Pliers, Safety Glasses &2, 100 Watt, Type A Medium
Base Bulbs.
H
C
-
-
K
L
M
1OF3
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1:
a. Thread the Hex Nut end of the Stem inside of the Medium
Assembly into the Hex Coupling on the bottom center of
the Upper Assembly. Using pliers, thread the Hex Nut
against the Hex Coupling and tighten until snug.
b. Locate the Medium Assembly upward and fit the Stud into
one of the Side Arm on the Upper Assembly. Secure by
threading the Hex Coupling end of the Stem inside of the
Base Assembly onto the end of the Stem inside of the
Medium Assembly. Using pliers, hand tighten until snug.
c. Fit the Stud onto the top of the Base Assembly into the Side
Rod of the Medium Assembly, which is lined up the Side
Arm of Upper Assembly to fit the Stud on Medium
Assembly. Pass the Washer over the Stem inside of the
Base Assembly, by using the Wrench, thread the Hex Nut
onto the Stem to secure the above parts together. Hand
tighten until snug.
Side Arm
Stud
STYLE NUMBER Q611F:
UpperAssembly
Hex Coupling
Hex Nut
Stem
Side Rod
Stud
MediumAssembly
Hex Coupling
Stem
BaseAssembly
Washer
Hex Nut
Wrench
2OF3
Page 3
ASSEMBLY INSTRUCTIONS
STYLE NUMBER Q611F:
STEP 2:
a. Thread the Hex Nut end of the Nipple with Hex Nut into the
Hex Coupling on the top center of the Junction Box. Using
pliers, thread the Hex Nut against the Hex Coupling and
tighten until snug.
b. Pass the Spacer Tube, the Check Ring, the center hole of
the Shade, the Diffuser and the Rubber Washer over the
top end of the Nipple. Secure by threading the Finial onto
the Nipple and hand tighten until snug.
Shade
Junction Box
Diffuser
Spacer Tube
Hex Coupling
Finial
Rubber Washer
Check Ring
Nipple with Hex Nut
STEP 3
a Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
.
:
Your assembly is completed now. Retain this sheet for future reference.
3OF3
Loading...